Intermec CN70 hard reset

Intermec CN70 CN70e hard reset

Resetting the Computer
If the computer does not resume after pressing the Power button, or if the computer or an application locks up, you may need to reset the
computer. The computer uses the configuration currently saved in flash memory during the boot process. There are three ways to reset the
computer:
• Reboot
• Cold boot
• Clean boot
Rebooting the Computer
You may need to reboot the computer to correct conditions where an application stops responding to the system.
To reboot the computer:
• Press the Power button and select Reboot from the menu.
The computer systematically shuts down, restarts, and goes through the initialization process.

Cold Booting the Computer

In some cases where the computer completely stops responding, it may be necessary to perform a cold boot or hard reset. Because cold booting may result in data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset.
All other data, such as configuration and network settings, is preserved.

To cold boot the mobile computer:
1 Press the Power button to suspend the computer.
2 Remove the handstrap and the battery pack.
3 Press the Reset button in the battery compartment on the back of the computer.
4 Replace the battery and the handstrap.
5 Press Power and wait while the mobile computer boots. When the cold boot is complete, the Home screen appears.

Clean Booting the Computer

A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of
those found in the Flash File Store, or any removeable storage.

If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and
running for further troubleshooting. You can clean boot using the mobile computer, or you can clean boot using the SmartSystems
Console:
To perform a clean boot using the mobile computer:
1 Remove the battery pack from the back of the computer.
2 With a stylus, press the Reset button in the battery cavity.
3 Insert the battery back into the computer, and immediately press and hold the Power button and Volume Down button (the lower
button on the right side).
4 Continue to hold the Power button and the Volume Down button down until you are prompted to release them.
5 Press the Volume Up button on the right side to start the clean boot.
6 Wait for the computer to load files from its ROM.

To clean boot the computer using the SmartSystems Console:
• Right-click the 70 Series computer and select Intermec Power Tools > Clean Boot Device.

Intermec CN50 hard reset

Intermec CN50 hard reset

Resetting the Computer
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an
application locks up, you may need to reset the computer. The computer uses the configuration currently saved in flash memory
during the boot process. There are three ways to reset the computer:
• Warm booting the computer
• Cold booting the computer
• Clean booting the computer
Warm Booting the Computer
You may need to perform a warm boot to correct conditions where an application stops responding to the system.

To warm boot the computer:
1 Tap Start > Shut Down.
Or, scan this bar code.

The computer systematically shuts down.
2 Press the Power button to restart the computer. If the computer is connected to an external power supply, it automatically restarts

Cold Booting the Computer
In some cases where the computer completely stops responding, it may be necessary to perform a cold boot. Because cold booting may result
in data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the CN50 does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset.
All other data, such as CN50 configuration and network settings, is preserved.

To cold boot your computer:
1 If possible, tap Start > Shut Down.
2 Remove the battery pack from the CN50 and wait 30 seconds.
3 Reinsert the battery pack and press the Power button.

Clean Booting the Computer
If the computer seems to be locked up, try warm booting and then cold booting the computer. If neither method works, use a clean boot to get
the computer up and running for further troubleshooting. When you clean boot, the computer only loads files and applications that are
absolutely required by the operating system. A clean boot returns the computer to an “out of the box” or factory default state, so that you
can run diagnostic tests to troubleshoot the normal boot processes.

The clean boot process erases the computer memory, including all applications and data files in the object store. To preserve
applications through a clean boot, store them in the Flash File Store.

To clean boot the computer using the mobile computer:
1 Remove the battery pack from the back of the CN50.
2 Reinsert the battery pack and press the Power button.
3 When the CN50 starts the boot process, simultaneously press < and > until the IPL Boot Configuration Menu appears on the
screen.

4 Press 2 to select Force Clean Boot and then press 0 to select Continue with Boot.
The CN50 executes the clean boot. This process takes a few minutes.
5 When prompted, tap the screen to set up the CN50.
6 Follow the instructions to calibrate the screen.

Intermec CN4e hard reset

Intermec CN4e hard reset

Resetting the CN4e
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an
application locks up, you may need to reset the CN4e. The CN4e uses the configuration currently saved in flash memory during the boot
process. There are three ways to reset the CN4e:
• Warm booting the CN4e

• Cold booting the CN4e

• Clean booting the CN4e
Warm Booting the CN4e
You may need to perform a warm boot to correct conditions where an application stops responding to the system.
To warm boot the computer
• Press and hold the Power button for 10 seconds.
Or,
• Right-click on the CN4e via the SmartSystems console and select
Intermec Power Tools > Warm Boot Device.
The computer systematically shuts down, restarts, and goes through the initialization process.
Cold Booting the CN4e
In some cases where the computer completely stops responding, you may need to perform a cold boot. Because cold booting may result in
data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the CN4e does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All
other data, such as CN4e configuration and network settings, is preserved.

To cold boot your CN4e
1 Press the Power button to suspend the CN4e.
2 Remove the battery pack from the CN4e.
3 Use the stylus to press the Reset button on the back of the CN4e.

(CN4e reset button location is similar to CN4)

Clean Booting the CN4e

A clean boot erases the memory in the mobile computer, including all applications and data files found in the ObjectStore,
and loads only the default files and programs required by the CN4e operating system.
During a clean boot, the CN4e first looks for the SSPB files on an installed miniSD card. If no card is found, the CN4e loads the
SSPB files in the Flash File Store. Files found on a miniSD card during a clean boot are copied into the Flash File Store and
overwrite the existing SSPB files.

If the CN4e seems to be locked up, try warm booting and then cold booting the computer. If neither method works, use a clean boot to
get the CN4e up and running for further troubleshooting.
The clean boot process is as follows:
• initial boot > SSPB installation > reboot > DCE installation > SRs copied to CabFiles folder > _sstransferagent.xml run > reboot >
CabFiles folder contents run > reboot, if required.
To clean boot the computer
1 Press the Power button to suspend the CN4e.
2 Remove the battery pack from the back of the CN4e.
3 Use the stylus to press the Reset button on the back of the CN4e.

4 Insert the battery pack into the CN4e, and immediately press and hold the Power button and both buttons on the left side.
5 Continue to hold the Power button and both buttons on the left side until a Warning message appears on the display.
6 Release the Power button and both buttons on the left side, read the message, and press either button on the right side to continue.
7 Wait for the CN4e to load files from its ROM.

Note: You can also clean boot the CN4e using the SmartSystems console. To clean boot the CN4e using the SmartSystems console,
right-click the CN4e and select Intermec Power Tools > Clean Boot Device.

Intermec CN4 hard reset

Intermec CN4 hard reset

Resetting the CN4
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an
application locks up, you may need to reset the CN4. The CN4 uses the configuration currently saved in flash memory during the boot
process. There are three ways to reset the CN4:
• Warm booting the CN4

• Cold booting the CN4

• Clean booting the CN4
Warm Booting the CN4
You may need to perform a warm boot to correct conditions where an application stops responding to the system.
To warm boot the computer
• Press and hold the Power button for 10 seconds.
Or,
• Right-click on the CN4 via the SmartSystems console and select
Intermec Power Tools > Warm Boot Device.
The computer systematically shuts down, restarts, and goes through the initialization process.
Cold Booting the CN4
In some cases where the computer completely stops responding, you may need to perform a cold boot. Because cold booting may result in
data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the CN4 does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All
other data, such as CN4 configuration and network settings, is preserved.

To cold boot your CN4
1 Press the Power button to suspend the CN4.
2 Remove the battery pack from the CN4.
3 Use the stylus to press the Reset button on the back of the CN4.

Clean Booting the CN4

A clean boot erases the memory in the mobile computer, including all applications and data files found in the ObjectStore,
and loads only the default files and programs required by the CN4 operating system.
During a clean boot, the CN4 first looks for the SSPB files on an installed miniSD card. If no card is found, the CN4 loads the
SSPB files in the Flash File Store. Files found on a miniSD card during a clean boot are copied into the Flash File Store and
overwrite the existing SSPB files.

If the CN4 seems to be locked up, try warm booting and then cold booting the computer. If neither method works, use a clean boot to
get the CN4 up and running for further troubleshooting.
The clean boot process is as follows:
• initial boot > SSPB installation > reboot > DCE installation > SRs copied to CabFiles folder > _sstransferagent.xml run > reboot >
CabFiles folder contents run > reboot, if required.
To clean boot the computer
1 Press the Power button to suspend the CN4.
2 Remove the battery pack from the back of the CN4.
3 Use the stylus to press the Reset button on the back of the CN4.

4 Insert the battery pack into the CN4, and immediately press and hold the Power button and both buttons on the left side.
5 Continue to hold the Power button and both buttons on the left side until a Warning message appears on the display.
6 Release the Power button and both buttons on the left side, read the message, and press either button on the right side to continue.
7 Wait for the CN4 to load files from its ROM.

Note: You can also clean boot the CN4 using the SmartSystems console. To clean boot the CN4 using the SmartSystems console,
right-click the CN4 and select Intermec Power Tools > Clean Boot Device.

Intermec CN3e hard reset

Intermec CN3e hard reset for Windows Mobile 5.0

Resetting the CN3e
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an application lock up, you may need to reset the CN3e. The CN3e uses the configuration currently saved in flash memory during the boot process. There are three ways to reset the CN3e:
• Warm booting the CN3e
• Cold booting the CN3e
• Clean booting the CN3e

Warm Booting the CN3e
You may need to perform a warm boot to correct conditions where an application stops responding to the system.
To warm boot the computer
• Press and hold the Power button for 10 seconds or right-click on the CN3e via the SmartSystems Console and select Intermec
Power Tools > Warm Boot Device.
The computer systematically shuts down, restarts, and goes through the initialization process.

Cold Booting the CN3e
In some cases where the computer completely stops responding, it may be necessary to perform a cold boot. Because cold booting may result in data loss, only use this method if all other recovery methods have failed.

Note: Cold booting the CN3e does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All other data is preserved.

To cold boot your CN3e
1 Press the Power button to suspend the CN3e.
2 Remove the battery pack from the CN3e.
3 Press the Reset button on the back of the CN3e.

Locating the Reset Button on the CN3e

Clean Booting the CN3e

When you clean boot the CN3e, it loads only those files and programs that are absolutely required by the operating system. Use the clean boot to troubleshoot the CN3e by getting it up and running so that you can perform diagnostic tests to determine which elements of the normal boot process are causing problems.

The clean boot process will erase the memory in the mobile computer, including all applications and data files found in the
object store.
A clean boot will load files from the Flash File Store if an SSPB files are not on a miniSD card. If SSPB files are on a miniSD card,
they will overwrite the files in the Flash File Store.

To clean boot the computer

1 Press the Power button to suspend the CN3e.
2 Remove the battery pack from the back of the CN3e.
3 With a stylus, press the Reset button on the battery cavity.
4 Insert the battery pack into the CN3e and immediately press and hold the Power button and both buttons on the left side.
5 Continue to hold the Power button and both buttons on the left side until a Warning message appears on the display.
6 Release the Power button and both buttons on the left side, read the message, and press either button on the right side to continue.
7 Wait for the CN3e to load files from the miniSD card.

Note: You can also clean boot the CN3e using the SmartSystems console. To clean boot the CN3e using the SmartSystems Console,
right-click on the CN3e and select Intermec Power Tools > Clean Boot Device.

There are no user-serviceable parts inside the CN3e. Opening the CN3e will void the warranty and may cause damage to the internal components.

Intermec CN3 hard reset

Intermec CN3 hard reset for Windows Mobile 5.0

Resetting the CN3
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an application lock up, you may need to reset the CN3. The CN3 uses the configuration currently saved in flash memory during the boot process. There are three ways to reset the CN3:
• Warm booting the CN3
• Cold booting the CN3
• Clean booting the CN3

Warm Booting the CN3
You may need to perform a warm boot to correct conditions where an application stops responding to the system.
To warm boot the computer
• Press and hold the Power button for 10 seconds or right-click on the CN3 via the SmartSystems Console and select Intermec
Power Tools > Warm Boot Device.
The computer systematically shuts down, restarts, and goes through the initialization process.

Cold Booting the CN3
In some cases where the computer completely stops responding, it may be necessary to perform a cold boot. Because cold booting may result in data loss, only use this method if all other recovery methods have failed.

Note: Cold booting the CN3 does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All other data is preserved.

To cold boot your CN3
1 Press the Power button to suspend the CN3.
2 Remove the battery pack from the CN3.
3 Press the Reset button on the back of the CN3.

Locating the Reset Button on the CN3

Clean Booting the CN3

When you clean boot the CN3, it loads only those files and programs that are absolutely required by the operating system. Use the clean boot to troubleshoot the CN3 by getting it up and running so that you can perform diagnostic tests to determine which elements of the normal boot process are causing problems.

The clean boot process will erase the memory in the mobile computer, including all applications and data files found in the
object store.
A clean boot will load files from the Flash File Store if an SSPB files are not on a miniSD card. If SSPB files are on a miniSD card,
they will overwrite the files in the Flash File Store.

To clean boot the computer

1 Press the Power button to suspend the CN3.
2 Remove the battery pack from the back of the CN3.
3 With a stylus, press the Reset button on the battery cavity.
4 Insert the battery pack into the CN3 and immediately press and hold the Power button and both buttons on the left side.
5 Continue to hold the Power button and both buttons on the left side until a Warning message appears on the display.
6 Release the Power button and both buttons on the left side, read the message, and press either button on the right side to continue.
7 Wait for the CN3 to load files from the miniSD card.

Note: You can also clean boot the CN3 using the SmartSystems console. To clean boot the CN3 using the SmartSystems Console,
right-click on the CN3 and select Intermec Power Tools > Clean Boot Device.

There are no user-serviceable parts inside the CN3. Opening the CN3 will void the warranty and may cause damage to the internal components.

To clean the imager window, camera window, and touch screen
1 Press the Power button to suspend the CN3.
2 Dip a clean cloth towel in the ammonia solution and wring out the excess.
3 Wipe off the imager window, camera lens, and flash area. Do not allow any abrasive material to touch these surfaces.
4 Wipe dry.

Intermec CK71 hard reset

Intermec CK71 hard reset

Resetting the Computer
If the computer does not resume after pressing the Power button, or if the computer or an application locks up, you may need to reset the
computer. The computer uses the configuration currently saved in flash memory during the boot process. There are three ways to reset the
computer:
• Reboot
• Cold boot
• Clean boot
Rebooting the Computer
You may need to reboot the computer to correct conditions where an application stops responding to the system.
To reboot the computer:
• Press the Power button and select Reboot from the menu.
The computer systematically shuts down, restarts, and goes through the initialization process.

Cold Booting the Computer

In some cases where the computer completely stops responding, it may be necessary to perform a cold boot or hard reset. Because cold booting may result in data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset.
All other data, such as configuration and network settings, is preserved.

To cold boot the mobile computer:
1 Press the Power button to suspend the computer.
2 Remove the handstrap and the battery pack.
3 Press the Reset button in the battery compartment on the back of the computer.
4 Replace the battery and the handstrap.
5 Press Power and wait while the mobile computer boots. When the cold boot is complete, the Home screen appears.

Clean Booting the CK71 Computer

A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of
those found in the Flash File Store, or any removeable storage.

If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and
running for further troubleshooting. You can clean boot using the mobile computer, or you can clean boot using the SmartSystems
Console:
To perform a clean boot using the mobile computer:
1 Remove the battery pack from the back of the computer.
2 With a stylus, press the Reset button in the battery cavity.
3 Insert the battery back into the computer, and immediately press and hold the Power button and Volume Down button (the lower
button on the right side).
4 Continue to hold the Power button and the Volume Down button down until you are prompted to release them.
5 Press the Volume Up button on the right side to start the clean boot.
6 Wait for the computer to load files from its ROM.

To clean boot the computer using the SmartSystems Console:
• Right-click the CK71 computer and select Intermec Power Tools > Clean Boot Device.

Intermec CK70 hard reset

Intermec CK70 hard reset

Resetting the Computer
If the computer does not resume after pressing the Power button, or if the computer or an application locks up, you may need to reset the
computer. The computer uses the configuration currently saved in flash memory during the boot process. There are three ways to reset the
computer:
• Reboot
• Cold boot
• Clean boot
Rebooting the Computer
You may need to reboot the computer to correct conditions where an application stops responding to the system.
To reboot the computer:
• Press the Power button and select Reboot from the menu.
The computer systematically shuts down, restarts, and goes through the initialization process.

Cold Booting the Computer

In some cases where the computer completely stops responding, it may be necessary to perform a cold boot or hard reset. Because cold booting may result in data loss, use this method only if all other recovery methods have failed.

Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset.
All other data, such as configuration and network settings, is preserved.

To cold boot the mobile computer:
1 Press the Power button to suspend the computer.
2 Remove the handstrap and the battery pack.
3 Press the Reset button in the battery compartment on the back of the computer.
4 Replace the battery and the handstrap.
5 Press Power and wait while the mobile computer boots. When the cold boot is complete, the Home screen appears.

Clean Booting the CK70 Computer

A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of
those found in the Flash File Store, or any removeable storage.

If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and
running for further troubleshooting. You can clean boot using the mobile computer, or you can clean boot using the SmartSystems
Console:
To perform a clean boot using the mobile computer:
1 Remove the battery pack from the back of the computer.
2 With a stylus, press the Reset button in the battery cavity.
3 Insert the battery back into the computer, and immediately press and hold the Power button and Volume Down button (the lower
button on the right side).
4 Continue to hold the Power button and the Volume Down button down until you are prompted to release them.
5 Press the Volume Up button on the right side to start the clean boot.
6 Wait for the computer to load files from its ROM.

To clean boot the computer using the SmartSystems Console:
• Right-click the CK70 computer and select Intermec Power Tools > Clean Boot Device.

Intermec CK32IS hard reset

Intermec CK32IS hard reset

Resetting Your Computer
You may need to reset your computer if:
• the CK32 I-Safe completely stops responding
• an application is locked up and stops responding
• when you upgrade the firmware
• when you reflash the CK32 I-Safe
Preferred Reset Method
This procedure is the recommended method in recovering the CK32 I-Safe. It performs a graceful system shutdown and no data
is lost in the process.
To recover the CK32 I-Safe
• Press and hold the Power button for about 10 seconds.
Secondary Reset Method
If performing the preferred reset method does not restore system operation, try using the secondary reset method. This method
does not guarantee that cached disk data will be saved, and as such, transactional data may be lost during the reset. All other
data is preserved.
To press the reset switch
1 Press the Power button to suspend the CK32 I-Safe.
2 With a bent paper clip or similar device, press the recessed reset switch on the CK32 I-Safe keypad.

Performing a Clean Boot

If performing either reset method fails to restore system operation, you may have to perform a clean boot. This is a boot
method which formats the Object Store (user store) to clean data and registry information from the CK32 I-Safe system and
restore them to their factory-default state.

The clean boot process will erase the memory in the CK32 ISafe, including all applications and data files found in the
object store.
To preserve application programs through a clean boot they must be stored in the Flash File Store.

To perform a clean boot
1 Press the Power button to suspend the CK32 I-Safe.
2 With a bent paper clip or similar device, press the recessed reset switch on the CK32 I-Safe keypad.
3 Press and hold the Power button until a Warning message appears on the display, release the Power button, then read
the message.
4 Press and release the right side of the Scan button to perform a clean boot. Press and release the left side of the Scan button
to cancel the clean boot.

Intermec CK3 hard reset

Intermec CK3 hard reset

Resetting the CK3
You seldom need to reset the CK3. However, you do need to reset the CK3 when an application is locked up and does not respond, when
you upgrade the firmware, or when you reflash the CK3. The CK3 uses the configuration currently saved in flash memory during the
reset process.
There are three ways to reset the CK3:
• Warm boot
• Cold boot
• Clean boot
Warm Booting the CK3
If your CK3 has a charged battery installed but does not resume after you press the Power key, or if the computer or an application is locked
up, you may need to warm boot the CK3.
To warm boot your CK3
• Press and hold POWER for 5 seconds.
Or,
• From the SmartSystems console, right-click the CK3 and select
Intermec Power Tools > Warm Boot Device.
The CK3 shuts down, restarts, and goes through the initialization process.
Cold Booting the CK3
If the CK3 or application is locked up and does not respond to a warm boot, follow this procedure to perform a cold boot.
Performing a cold boot may result in data loss. When you cold boot the CK3, cached disk data may not be saved, so
transactional data may be lost.

To cold boot your CK3
1 Press and hold Power key for about 2 seconds to suspend the CK3.
2 Remove the battery.
3 Use the stylus to press the reset button in the battery compartment of the CK3.

Do not use force or a sharp object when pressing the reset button. You may damage the reset button.

4 Replace the battery.

Clean Booting the CK3
If the CK3 does not warm boot or cold boot, you may need to perform a clean boot. When you clean boot the CK3, the CK3 only loads files
and applications that are absolutely required by the operating system.
Perform a clean boot to get the CK3 up and running so that you can run diagnostic tests to troubleshoot the normal boot process.
Reset button
Do not use force or a sharp object when pressing the reset button. You may damage the reset button.
The clean boot process erases the CK3 memory, including all applications and data files in the object store. To preserve
applications through a clean boot, store them in the Flash File Store.

To clean boot the CK3
1 Press and hold Power button for about 2 seconds to suspend the CK3.
2 Remove the battery.
3 Use the stylus to press the reset button in the battery compartment of the CK3

4 Replace the battery.
5 Press and hold both Power button and the PTT button.
6 Continue to hold Power button and PTT until the “Clean boot the system?” prompt appears on screen.
7 Release the two buttons, read the message, and press the
appropriate button to either proceed with the clean boot or cancel the clean boot.
Reset button
Note: You can also clean boot your CK3 from the SmartSystems console: right-click the CK3 and select Intermec Power Tools >
Clean Boot Device.

Intermec CK30 hard reset

WARM BOOT:
Press and hold I/O for 5 seconds
COLD BOOT:
Remove the battery. Press the reset switch

Intermec CS40 hard reset

Resetting the Computer
You rarely need to reset the computer. If the computer does not resume after pressing the Power button, or if the computer or an
application locks up, you may need to reset the computer. The computer uses the configuration currently saved in flash memory
during the boot process. There are three ways to reset the computer:
• Warm booting the computer
• Cold booting the computer
• Clean booting the computer
Warm Booting the Computer
You may need to perform a warm boot to correct conditions where an application stops responding to the system. There are two ways to do
this:
To warm boot the computer:
1 Tap Start > Programs > Shut Down.
Or, scan this bar code.

The computer systematically shuts down.
2 Press the Power button to restart the computer. If the computer is connected to an external power supply, it automatically restarts.

Cold Booting the Computer
In some cases where the computer completely stops responding, you may need to perform a cold boot. Cold booting may result in data loss,
so use this method only if all other recovery methods have failed.
Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset.
All other data, such as computer configuration and network settings, is preserved.

To cold boot your computer:
1 If possible, tap Start > Programs > Shut Down.
2 Remove the battery pack from the computer and wait at least 30
seconds.
3 Install the battery pack and press the Power button.

Clean Booting the Computer

A clean boot erases the memory in the mobile computer,
including all applications and data files found in the ObjectStore, and loads only the default files and programs required by the
computer operating system.
During a clean boot, the computer first looks for the SSPB files on an installed microSD card. If no card is found, the computer loads
the SSPB files in the Flash File Store. Files found on a microSD card during a clean boot are copied into the Flash File Store and
overwrite the existing SSPB files.

If the computer seems to be locked up, try warm booting and then cold booting the computer. If neither method works, use a clean boot to get
the computer up and running for further troubleshooting.
To clean boot the computer:
1 Remove the battery pack from the computer and wait at least 30 seconds.
2 Install the battery pack and press the Power button.
3 When the computer starts the boot process, simultaneously press and hold < and > until the IPL Boot Configuration Menu appears.

4 Press 2 to select Force Clean Boot, and then press 0 to select Continue with Boot.
The computer clean boots. This process takes a few minutes.
5 When prompted, tap the screen to set up the computer.
6 Follow the instructions to align the screen.

Kyocera Brio hard reset 100% tested way

Kyocera Brio soft reset

Resetting the phone
If the screen seems frozen and the keypad does not respond to keypresses, reset the phone by completing the following steps:
1. Remove the battery cover.
2. Remove and replace the battery.

Kyocera Brio hard reset

Reset Your Phone and Phone Content
This option lets you clear different types of personal information stored on your phone, reset your phone to factory settings, or both.
1. Press OK > Settings > Reset/Delete.
2. Enter your lock code.
3. Highlight an option and press .
Reset Settings to restore all the factory defaults, including ringer types and display settings. Contacts, History, Calendar, and Messaging are not affected.
Reset Phone to reset all settings and erase all data on your phone.
4. Read the message and press the left softkey (RESET SETTINGS or RESET PHONE).

Kyocera Rio E3100 hard reset

Kyocera Rio E3100 soft reset

Resetting the phone
If the screen seems frozen and the keypad does not respond to keypresses, reset the phone by completing the following steps:
1. Remove the battery cover.
2. Remove and replace the battery.

Press ##786. Be careful when you reset as your phone will be completely reset. Once it reboots you will have to reprogram your 10 digit phone number into the phone. This can be done by dialing ##000000# and then choosing the edit mode and entering your 10 digit number in both fields.

If the problem persists, return the phone to the dealer for service.

 

try this way i hope solve this problem

Kyocera Torino S2300 hard reset

Kyocera Torino S2300 soft reset

Resetting the phone
If the screen seems frozen and the keypad does not respond to keypresses, reset the phone by completing the following steps:
1. Remove the battery cover.
2. Remove and replace the battery.

If the problem persists, return the phone to the dealer for service.

 

try this way 100% tested way i solve this phone tnx

Kyocera Milano hard reset using hardware keys

Turn off Kyocera Milano. Press and hold Volume down + press and hold the Power key.
Press the Volume down key to scroll to wipe data/factory reset.
Select Yes -- delete all user data and confirm with Menu key, then repeat it with wipe cache partition then select reboot now.
Confirmation key is MENU key.

Kyocera Milano Factory Data Reset

Your device’s Privacy menu includes the Factory data reset option. This option lets you reset your device to the original factory settings, which erases all data from the device’s application storage, including:
● Your Google account
● All other email and social networking accounts
● System and application data and settings
● Downloaded applications
To reset your device:
1. Press Home > Menu , and touch Settings > Privacy > Factory data reset. Read the Factory data reset information.
2. Touch Reset phone.
3. Touch Erase everything. Your device will power down and reset itself, which may take up to 10 minutes.
Once the device has reset, it will run through the Hands Free Activation and update processes again. When finished, you will see the Welcome screen and Setup application.

Update Your Device Firmware:
1. Press Home > Menu , and touch Settings > About phone > System update.
2. Touch Update firmware. (Your device automatically downloads and installs any available updates. You may be required to power your device off and back on to complete the software upgrade.)

Kyocera Zio M6000 hard reset 100% tested me

Kyocera Zio M6000 hard reset

First try this: Dial ##4357* Scroll down to reset and enter 000000 code

Resetting the phone
If the screen seems frozen and the keypad does not respond to
key presses, reset the phone by completing the following steps:
1. Remove the battery cover.
2. Remove and replace the battery.

Kyocera Zio M6000 Factory Data Reset

To delete all data from your phone, touch HOME / Menu > Settings > Factory data reset > Reset phone.

Sharp Cricket Sanyo Kyocera Zio M6000 Too many pattern attempts

With the phone turned off press volume down + camera button + power button together, preess power button to select factory data reset.

Info screen

With the M6000 turned off press and hold END button for 3 sec then keep pressing END key + press CALL key for another few sec.

OR

Master Reset code for Zio
Emergency Dial
##4357*
Scroll down to reset and enter code-000000

OR

PRESS THE VOLUME DOWN + END CALL + THE CAMERA BUTTONS together. Go down to Factory Reset.

OR

1. Press Volume Up + Call Key + Track Ball + End Key to fastboot
2. Connect your phone to PC (and install android SDK on your PC)
3. Open command prompt (cmd.exe)
4. Navigate to your android\tools folder. *
5. Type fastboot -w

To navigate to tools folder: type in on your PC's CMD command prompt window Start > Run : Enter cmd

cd c:\android-sdk-windows
cd tools
fastboot -w

WARNING: All your data will be lost!

 

try this way i hope solve your problem

Lenovo ET980 hard reset 100% tested way try this

Lenovo ET980 soft reset reboot

Lenovo ET980 Soft Reset Button: For system reset and keep SDRAM data.
click the Reset key with the touchpen, which will restart the system. If the fault does not disappear, power on the mobile phone with cold boot operation.

Lenovo ET980 Cold boot

Hold the ON/OFF key and the RESET key together for at least 5 seconds and then release these two keys simultaneously.
Any exchanging of the main battery should be finished within 20 minutes. Otherwise the backup battery may fail to support features such as the system clock, which may lead to power-on failure.


Attention: The cold boot operation will lead to the loss of system clock settings. If the fault doesn’t disappear after cold boot, choose "Restore factory settings".
Note: The steps of "Restore factory settings": Press the RECORD key and the roller’s Down key simultaneously, and then click the RESET key with the touchpen. In the middle of the screen displayed, choose OK item continuously with the Roller key, and then press the Roller Confirm key.

Lenovo ET980 Software Updating

Software updating for ET980 consists of Eboot updating, IPL updating and system updating. This section describes the updating operations. A complete updating procedure should follow the order given below:

Eboot updating ==> IPL updating ==> system updating

Hold the RECORD key. Click and release the Reset key, and the system enters the Eboot mode. Release the RECORD key. Now the Eboot version number is displayed at the bottom of the screen, as shown in the picture given below.



IPL Updating
Hold the RECORD key (Reset key) and the screen illustrated by (1) will be displayed. Choose the sixth option ("update ipl image"), and the screen shown by (2) appears.

Connect the mobile phone and the PC with a USB cable. On the PC end, open the updating program file.

Browse the PC to find the file IPL.nb0. Click "Start updating". When the IPL updating is finished.
Hold the RECORD key (Reset key) and the screen illustrated by left figure given below will be displayed. Choose the forth option ("update eboot image").
Connect the mobile phone and the PC with a USB cable. On the PC end, open the updating program file and choose the file for Eboot updating.
Click "Start updating". When the Eboot updating is finished.
System Updating
Hold the RECORD key (reset key) and the screen illustrated by left figure given below will be displayed. Choose the fifth option ("update system image").
Connect the mobile phone and the PC with a USB cable. On the PC end, open the updating program file and choose the file for system updating.
Click "Start updating". When the system updating is finished.
Notes:

1. After the updating program is started on the PC, when browsing for the updating file to be used, "All Files (*.*)" should be chosen for the file type. Otherwise the updating file will not be shown.

2. The chosen updating file should be matched with the selected updating option. If an option is mistakenly chosen, press and hold the RECORD key (Reset key) to choose again. The steps are simple, but operations should be performed with caution. If the updating is done with an unmatched file, the JTAG tool has to be used to format the mobile phone.

Lenovo ET960 hard reset 100% tested way try this

hard reset Lenovo ET960

Press Today + Camera + End buttons keys + RESET

Lenovo A60 hard reset 100% tested wat try this

Lenovo A60 hard reset dual SIM phone

Power off your Lenovo A60 phone.
Press  Volume UP + Power on the phone. In the recovery menu use Volume buttons to select
Wipe data/Factory reset and use power to confirm.
You can also select wipe cache partion to Reset your A60 phone.

Press Power and choose recovery.

Press and hold Camera + POWER buttons to get into download mode.

Lenovo A60 firmware upgrade download mode

You must save both of your IMEI number! Both IMEI for 1st and 2nd SIM slot too.

the soft way:

1. From the Home screen, press the Menu Key and touch Settings.
2 Touch the Privacy
4 Touch Factory data reset.
5 Touch Reset phone.
6 Touch Erase everything.

Lenovo A750 hard reset

Lenovo A750 hard reset dual SIM phone Be careful!!!

save everything. Back up your data.

Press and hold Camera + POWER buttons to get into factory mode.

Lenovo A750 reset code 1234. Be very careful!!! Some say that after reset they can't connect to any network.

You must save both of your IMEI number! Both IMEI 1st and 2nd too.

the soft way:

1. From the Home screen, press the Menu Key and touch Settings.
2 Touch the Privacy
4 Touch Factory data reset.
5 Touch Reset phone.
6 Touch Erase everything.

Lenovo K800 hard reset

Lenovo K800 hard reset

1. From the Home screen, press the Menu Key and touch Settings.
2 Touch the Privacy
4 Touch Factory data reset.
5 Touch Reset phone.
6 Touch Erase everything.

If you know Lenovo K800 hard reset using buttons / keys pls leave comment.

LG G2 hard reset

Performing an LG G2 hard reset / LG G2 factory reset

Hard Reset (Factory Reset) How to unlock LG G2 password reset
If you forget your lock sequence and backup PIN, you will have to perform a hard reset to gain access to your phone.
WARNING
Performing a hard reset deletes all of your user data, which includes pictures, videos, and music saved to your internal memory. Please make sure to back up your information prior to performing a hard reset.
1. Turn the phone off.
2. Press and hold the following keys at the same time: Volume Down Key + Power/Lock Key on the back of the phone.
3. Release the Power/Lock Key only when the LG logo is displayed, then immediately press and hold the Power/Lock Key again.
4. Release all keys when the Factory hard reset screen is displayed.
5. Press the Power/Lock Key to continue or either of the Volume Keys to cancel.
6. Press the Power/Lock Key once more to confirm or either of the Volume Keys to cancel.


Note: All of the contents, including content which you create or download, will be deleted after a factory reset.

Performing a LG G2 factory reset via settings

The most convenient way to do a factory reset is via the phone settings.
Press Home, press Menu, and touch Settings > Backup & reset
PERSONAL DATA

Factory data reset:

Allows you to erase all of the data on the phone.  Read the warning, then tap Reset phone at the bottom of the screen and Erase everything to confirm.

Performing a LG G2 soft reset Power reset

In the case of a malfunction or lock up error, press and hold the Power/Lock Key for 8 seconds to reset the phone.