Medion LIFE P4310 hard reset

Medion LIFE P4310 soft reset

Just take out battery and reinsert it.

Medion LIFE P4310 hard reset MD 98910

1. Power off the phone
2. Press and keep pressed Volume UP and HOME and press Power for about 2-3 seconds
3. Use Volume key to move to "WIPE DATA / FACTORY RESET"
4. Confirm option pressing BACK button
5. Move to "Yes --delete all data" and confirm pressing BACK button
6. After operation press Back button once again to restart phone.

Medion MDPNA 100 hard reset

RESETTING THE Medion PNA 100

There are two options for resetting the Pocket PC.
SOFT-RESET
This option restarts the Pocket PC, without reinstallation being necessary. A soft-reset is often used in order to reorganize the
memory. In doing so all programs that are running are interrupted and the working memory is reinitialized.
Choose this option if your Pocket PC is not responding or working properly.

Perform the soft-reset as follows:

1. If possible save the files that your Pocket PC has just been processing.
2. Press the tip of the stylus into the soft-reset switch opening.
After a few seconds the Pocket PC displays the start screen.
Your configuration and your saved files will not be deleted.

Medion PNA100 HARD-RESET

Warning: A hard-reset deletes all data on your Pocket PC and causes a new initial installation.
It is not necessary to install the software on your synchronisation computer again, however.
Perform the hard-reset as follows:
1. If possible save all the files needed from your Pocket PC. To do this use the programs bundled with the Pocket PC.
2. Hold down the On/Off switch and carry out a soft-reset as described above.

Medion MDPPC 100 hard reset

Medion PPC 100 soft reset

Press the reset button

Medion PPC 100 hard reset

Hold down the On/Off switch and carry out a soft-reset as described above.

To turn ON Medion PPC 100 after hard reset or the first time
1. Remove the stylus from the holder and turn the cap as shown in the diagram.
2. Use the small point on the inside of the cap to turn the power switch to the ON position.
• The brand logo appears and after 30 seconds the Pocket PC displays the Windows welcome screen.
3. Screw the cap back onto the stylus.
4. Tap on the screen once with the stylus and follow the instructions that appear.
• Settings that you now make can be altered later.
• Warning: Always leave the power switch in the ON position. If the switch is placed in the OFF position, all data will be lost from your Pocket PC and you will need to perform the initial setup again.

Medion MDPPC 150 hard reset

RESETTING THE POCKET PC
There are two options for resetting the Pocket PC.

Medion PPC 150 SOFT-RESET

This option restarts the Pocket PC, without reinstallation being necessary. A soft-reset is often used in order to reorganize the
memory. In doing so all programs that are running are interrupted and the working memory is reinitialized.
Choose this option if your Pocket PC is not responding or working properly.

Perform the soft-reset as follows:
1. If possible save the files that your Pocket PC has just been processing.
2. Press the tip of the stylus into the soft-reset switch opening.
After a few seconds the Pocket PC displays the start screen.
Your configuration and your saved files will not be deleted.



HARD-RESET
Warning: A hard-reset deletes all data on your Pocket PC and causes a new initial installation.
It is not necessary to install the software on your synchronisation computer again, however.

Perform the hard-reset as follows:

1. If possible save all the files needed from your Pocket PC. To do this use the programs bundled with the Pocket PC.
2. Hold down the On/Off switch and carry out a soft-reset as described above.

Medion MDPPC 250 hard reset

RESETTING THE Medion 250 POCKET PC

There are two options for resetting the Pocket PC. SOFT-RESET This option restarts the Pocket PC, without reinstalla-tion being necessary. A soft-reset is often used in or-der to reorganize the memory. In doing so all pro-grams that are running are interrupted and the work-ing memory is reinitialized. Choose this option if your Pocket PC is not responding or working properly.

Perform the soft-reset as follows:
1. If possible save the files that your Pocket PC has just been processing.
2. Press the tip of the stylus into the soft-reset switch opening. After a few seconds the Pocket PC displays the start screen.
Your configuration and your saved files will not be deleted.

Medion PPC 250 HARD-RESET

Warning: A hard-reset deletes all data on your Pocket PC and causes a new initial installation. It is not necessary to install the software on your syn-chronisation computer again, however.

Perform the hard-reset as follows:
1. If possible save all the files needed from your Pocket PC. To do this use the program BackupRestore which is pre-installed on the Pocket PC
2. Hold down the On/Off switch and carry out a soft-reset as described above.

Microsoft Surface hard reset

Microsoft Surface hard reset

How to Factory Reset Microsoft Surface RT.
To reset your Surface without logging in, please try the following:
1. Attach your Touch Cover / Type Cover.
2. Power on your Surface.
3. Press and hold the Left Shift key at the Login screen.
4. Press the Power icon.
5. Press Restart
Your surface should boot to a light blue screen with some options on it.
1. Click on Troubleshoot.
2. Click on Reset your PC.
3. Follow the prompts.

How to reset surface?

1. Factory Reset.
Go to tap Applications list > Settings > about > reset your tablet.

Windows RT
Press Windows key and Power buttons together, same as Alt+Ctrl + Del on previous Windows OS.

You can use Backup and Restore Center to restore backups.

As last resort you can restore the factory image from the recovery partition. The recovery partition on a Microsoft Surface unit is a hidden partition on the drive. You should not delete this partition to free disk space, because the partition contains a copy of the factory image.

To restore the factory image

Turn on your device and press the BACKSPACE  key.
Press F8 key.
Select Repair your computer and hit ENTER
After the recovery wizard (keyb. layout, user, pass etc.)
Select cmd Command prompt, and then open the D:\recovery directory.
Enter recovery.cmd and then hit the ENTER key. Wait until it finishes.
After restarting the device you need to go through the setup wizard.

MiTAC Mio 269 hard reset

Clearing the Mio 269 Memory

NOTE (for Mio 268 Only): Clearing the memory will cause the navigation software to lose. You must insert the Mio Map card to perform the automatic installation. In case the data in the Mio Map card is lost or damaged, perform the “Recover” procedure.
If your device still does not respond after being reset, you can use the following steps to clear the memory.
1. Disconnect all cables, including the AC adapter, from your device.
2. Use the stylus to slide the ON/OFF switch to the OFF (left) position.
3. For Mio 268 only: Insert the Mio Map card to your device.
4. Wait for 1 minute and then slide the switch back to the ON (right) position

5. Your device will perform the initial start up.

Medion MDPPC 200 hard reset

RESETTING THE Medion 200 POCKET PC

There are two options for resetting the Pocket PC. SOFT-RESET This option restarts the Pocket PC, without reinstallation being necessary. A soft-reset is often used in order to reorganize the memory. In doing so all programs that are running are interrupted and the working memory is reinitialized. Choose this option if your Pocket PC is not responding or working properly.

Perform the soft-reset as follows:

Press Reset Button. This will Restart your Pocket PC. (Soft-Reset)

Medion PPC 200 HARD-RESET

CAUTION: Always leave the backup battery switch in the ON position unless you need to perform a hard reset. A
hard reset will cause the memory of your Pocket PC to be cleared.

Warning: A hard-reset deletes all data on your Pocket PC and causes a new initial installation.
It is not necessary to install the software on your synchronisation computer again, however.

Perform the hard-reset as follows:
1. If possible save all the files needed from your Pocket PC. To do this use the program BackupRestore which is pre-installed on the Pocket PC



2. Slide the battery lock to the unlock position (1) and then open the battery door (2). Turn the backup battery switch in the OFF position.

3. Insert the projected parts of the battery into the battery compartment (3) and then fit the battery into place (4).
3. The backup battery switch should be set to the ON (right) position for normal operation.
Pull out the stylus and use it to slide the battery switch to the ON (right) position.

4. Replace the battery door and slide the battery lock to the lock position.

MiTAC Mio 168 hard reset

Resetting Your MiTAC Mio 168 Pocket PC

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:

After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side
of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

CAUTION: To ensure the integrity of your data should it be necessary to clear the memory, you’re
advised to regularly back up your data.

Do not slide the battery switch unless it is necessary

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping WIN Start > Settings > System tab > Memory icon > Running
Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Pocket PC will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.

8. Reestablish a partnership with your desktop computer.
9. You may also want to restore data to your Pocket PC from your most recent
backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 169 hard reset

MiTAC Mio 169 hard reset

Resetting Your MiTAC Mio 169 System
Resetting your system is similar to restarting your computer. Occasionally, you may need to reset your device. For example, you should reset your system when it stops responding; or appears to be “frozen” or “locked up.”
To reset your system, use the stylus pen to press the Reset button on top of your device.

If your device still does not respond after being reset, you can use the following steps to clear the memory, and reset the system settings to factory defaults.
1. Disconnect all cables, including the AC adapter, from your device.

2. Use the stylus pen to slide the ON/OFF switch to the OFF (right) position.
3. Wait for 1 minute and then slide the switch back to the ON (left) position.
4. Your device will automatically turn on and the Main screen will appear.
NOTE: Once you clear the memory with this ON/OFF switch, all the settings you have changed in the System Settings will be erased. You will need to re-enter any personal settings, including time and date once again.

MiTAC Mio 180 hard reset

Mio 180 Soft reset

Press the reset button to restart Digiwalker 180

Mio 180 hard reset

Follow this procedure to restore your Pocket PC to the last state when your Pocket PC does not respond after being reset.

1. Disconnect all cables, including the AC adapter, from your Pocket PC.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position. Mio 180 restarting after hard reset.

MiTAC Mio 268 hard reset

Clearing the Mio 268 Memory

NOTE (for Mio 268 Only): Clearing the memory will cause the navigation software to lose. You must insert the Mio Map card to perform the automatic installation. In case the data in the Mio Map card is lost or damaged, perform the “Recover” procedure.
If your device still does not respond after being reset, you can use the following steps to clear the memory.
1. Disconnect all cables, including the AC adapter, from your device.
2. Use the stylus to slide the ON/OFF switch to the OFF (left) position.
3. For Mio 268 only: Insert the Mio Map card to your device.
4. Wait for 1 minute and then slide the switch back to the ON (right) position

5. Your device will perform the initial start up.

MiTAC Mio 336 BT hard reset

Resetting Your MiTAC Mio 336 BT Pocket PC
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC;
for example, you should reset:
After you restore data from your desktop
computer.
When your Pocket PC stops responding; in other
words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side
of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected).
Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping WIN Start
Settings > System tab > Memory icon > Running
Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the
OFF (up) position.
5. Wait for 1 minute and then slide the switch back
to the ON (down) position.
6. Your Pocket PC will automatically turn on and
display the Welcome screen.
7. To begin the Welcome Wizard, tap the screen
with the stylus and follow the onscreen
instructions to complete the Welcome Wizard.

8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Pocket PC from your most recent
backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 338 hard reset

MiTAC Mio 338 soft reset

Press the reset hole on the left side of the Mio 338 to restart your PDA.

Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:
After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Pocket PC.

MiTAC Mio 338 hard reset

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping Win Start > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. The red notification indicator on your Pocket PC will flash for approximately 30 seconds. Then your Pocket PC will automatically turn on and display the Welcome screen.
7. To begin the Welcome Wizard, tap the screen with the stylus and follow the onscreen instructions to complete the Welcome Wizard.
8. Restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

MiTAC Mio 339 hard reset

Resetting Your Mio 339 Pocket PC

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your
Pocket PC; for example, you should reset:
After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the rear of your Pocket PC.


Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default state by clearing the memory (RAM) from your Pocket PC. For example, you should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping Start > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Remove the battery door.
5. Use the stylus to slide the battery switch to the OFF (left) position.
6. Wait for 1 minute and then slide the switch back to the ON (right) position.

7. The red notification indicator on your Pocket PC will flash for approximately 30 seconds. Then
your Pocket PC will automatically turn on and display the Welcome screen.
8. To begin the Welcome Wizard, tap the screen with the stylus and follow the onscreen instructions to complete the Welcome Wizard.
9. Reestablish a. partnership with your desktop computer.
10. You may also want to restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 558 hard reset

Resetting Your Pocket PC
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:
After you restore data from your desktop
computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket
PC:
1. Remove the SD/MMC and/or CompactFlash card (if installed).
2. Use the stylus to press the reset button on the rear of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:

When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Press the battery lock to remove the battery.
5. Use the stylus to slide the battery switch to the OFF (left) position.
6. Wait for 1 minute and then slide the switch back to the ON (right) position.
7. Your Pocket PC will automatically turn on and display the “Welcome” screen.
NOTE: In case your Pocket PC didn’t automatically turn on, use the stylus to firmly press the RESET button at the back
of your Pocket PC to turn it on.
8. To begin the Welcome Wizard, tap the screen with the stylus and follow the
onscreen instructions to complete the Welcome Wizard.

9. Reestablish a partnership with your desktop computer.
10. You may also want to restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

MiTAC Mio 8390 hard reset

Restoring Factory Default State
NOTE
You are recommended to ask your local dealer for service. Avoid restoring factory default state by yourself.
In some cases, you may need to restore your Smartphone to the factory default state by clearing the memory (RAM) from your Smartphone. For example, you should clear the memory:
When your Smartphone cannot be turned on.
When you forget your password.
When you want to remove the add-on software.
When you wish to return, dispose of, or sell your Smartphone.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.

Follow this procedure to clear the memory from your Smartphone:
1. To keep the data stored in your Smartphone, back up your data to your desktop computer using ActiveSync, and restore it after the memory is cleared.
2. Connect the AC adapter, and disconnect all other cables.
3. Make sure that your Smartphone is turned off.
4. Press and hold the Volume control. When holding it, press and hold the End key for four seconds to turn on your Smartphone, and then let go of the End key .
5. After the Smartphone vibrates twice, you can let go of the Volume control.
6. Your Smartphone will turn on after about two minutes.
7. Re-install the add-on software, if necessary.
8. Restore your backup, if necessary.

MiTAC Mio 8870 hard reset

Mio 8870 hard reset

Restoring Factory Default State

You are recommended to ask your local dealer for service. Avoid restoring factory default state
by yourself

In some cases, you may need to restore your Smartphone to the factory default state by
clearing the memory (RAM) from your Smartphone. For example, you should clear the
memory:

When your Smartphone cannot be turned on.
When you forget your password.
When you want to remove the add-on software.
When you wish to return, dispose of, or sell your Smartphone.

Clearing the memory means all data you have entered in RAM, including all files, system
settings and additional programs you have installed, will be erased.

Follow this procedure to clear the memory from your Smartphone:

1. To keep the data stored in your Smartphone, back up your data to your desktop computer
using ActiveSync, and restore it after the memory is cleared.
2. Connect the AC adapter, and disconnect all other cables.
3. Make sure that your Mio 8870 Smartphone is turned off.

4. Press and hold the Volume control. When holding it, press and hold the End key for four seconds to turn on your Smartphone, and then let go of the End key.

5. After the Smartphone vibrates twice, you can let go of the Volume control.
6. Your Smartphone will turn on after about two minutes.
7. Re-install the add-on software, if necessary.
8. Restore your backup, if necessary.

Yes tested this way try this way i hope solve your problem