AR.Drone hard reset

AR.Drone reset

Place the AR.Drone on a flat surface and press the Reset button.

Note: Flying is not possible with an emergency message on the screen.

Restarting the AR.Drone
To restart the AR.Drone, just disconnect and reconnect the battery.

Warning: Make sure that you have securely connected the AR.Drone battery and that the motor LEDs
are green before connecting your iPhone to the Wi-Fi network of the AR.Drone and before starting a
flight application.

The Emergency button
In the event of any problems while piloting the AR.Drone, just press the Emergency button.
Warning: Only press on the Emergency button in a genuine emergency. The motors will immediately cut
out and the AR.Drone will fall from whatever height it is currently at. In most scenarios, simply landing
the AR.Drone is enough to resolve any problems.

The Reset button
A message on the iPhone may indicate that it is necessary to re-initialise the AR.Drone. In this case,
press the Reset button.

AT&T Surround hard reset

Performing a AT&T Surround factory reset using phone buttons

If you cannot turn on your phone or access the phone settings, you can still perform a factory reset by using the buttons on the phone.

1. With the phone turned off, press and hold the VOLUME UP and DOWN buttons, and then briefly press the POWER button.
2. Wait for the screen to show the instructions on how to do the factory reset, and then release the VOLUME UP and DOWN buttons.
3. Follow the instructions onscreen to factory reset your phone.

All data will be lost!

Performing a AT&T Surround factory reset (hard reset)

1. On the Start screen, tap .
2. Tap Settings > about phone.
3. Tap reset your phone, and then tap yes.

AT&T Pure hard reset

Resetting AT&T Pure Your Device

Performing a soft reset

Perform a soft (normal) reset to clear all active program memory and shut down all active programs. This is useful when your device is running slower than normal, or a program is not performing properly. If a soft reset is performed when programs are running, unsaved work is lost.
To perform a soft reset
1. Pull out the stylus, then remove the back cover.
2. Use the stylus tip to press the RESET button (red) located at the opening of the stylus bay.
Your device restarts and displays the Home screen.
3. Replace the back cover and insert the stylus back into its compartment.

Performing a AT&T Pure hard reset

If a normal reset does not solve a system problem, you can perform a hard (full) reset. After a hard reset, the device is restored to its default settings—the way it was when you first purchased it and turned it on. You will lose any programs you installed, data you entered, and settings you customized on your device, and only Windows Mobile® software and other pre-installed programs will remain.
Warning! Your device will be set back to factory default settings. Make sure that any additional installed programs and/or user data have been backed up before you perform a hard reset.
Important If Encrypt files when placed on a storage card is enabled, backup all files from the storage card before using Clear Storage, hard reset, or updating the operating system. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.

To perform a AT&T Pure hard reset using buttons

1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:

3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.

Using Clear Storage

If you can access the device settings, you can use Clear Storage to reset your device back to factory default settings.
1. Tap Start > Settings > System > Clear Storage.

AT&T Aria hard reset

Performing an AT&T Aria hard/factory reset

You can return your phone to its original state, as it was when it left the factory. This is also called a hard reset. You might want to do this if you are giving your phone to a friend or relative and you want to remove all your data first, or if your phone has a persistent problem that is not solved by powering off the phone and then powering it on again.
A factory reset is a drastic measure. It permanently erases all your personal data and customized settings, and also removes any programs you have installed. Make sure that you have backed up the information and files you want to keep.

If your phone hangs or freezes, we recommend that you do a “soft” reset instead of a hard/factory reset. To perform a soft reset, remove the battery, wait for a few seconds, and then re-install it. After re-installing the battery, turn on the phone.

Performing an AT&T Aria factory reset via settings

The most convenient way to do a factory reset is via the phone settings.
Press HOME > MENU, then tap Settings.
Scroll down the screen, and then tap Privacy > Factory data reset.
On the Factory data reset screen, tap Reset phone, and then tap Erase everything.

Performing an AT&T Aria factory reset using phone buttons

If you cannot turn on your phone or access the phone settings, you can still perform a factory reset by using the buttons on the phone.
With the phone turned off, press and hold the VOLUME DOWN button, and then briefly press the POWER button.
Press VOLUME DOWN to select CLEAR STORAGE, and then press POWER to reset the device.

AT&T Tilt 2 hard reset

AT&T Tilt 2 Soft reset

Resetting Your AT&T Tilt2 Device

Performing a soft reset

Perform a soft (normal) reset to clear all active program memory and shut down all active programs. This is useful when your device is running slower than normal, or a program is not performing properly. If a soft reset is performed when programs are running, unsaved work is lost.

To perform a soft reset

1. Pull out the stylus.
2. Remove the back cover.
3. Use the stylus tip to press the RESET button located at the upper-left side of the open back panel.
Your device restarts and displays the Home screen.
4. Replace the back cover and insert the stylus back into its compartment.

AT&T Tilt 2 hard reset

Performing a hard reset

If a normal reset does not solve a system problem, you can perform a hard (full) reset. After a hard reset, the device is restored to its default settings—the way it was when you first purchased it and turned it on. You will lose any programs you installed, data you entered, and settings you customized on your device, and only Windows Mobile® software and other pre-installed programs will remain.

Warning! Your device will be set back to factory default settings. Make sure that any additional installed programs and/or user data have been backed up before you perform a hard reset.

Important If Encrypt files when placed on a storage card is enabled, backup all files from the storage card before using Clear Storage, hard reset, or updating the operating system. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.


To perform a Tilt 2 hard reset
1. With the device turned off, press and hold the TALK/SEND, END and POWER buttons until you see this message on the screen.

2. Release the TALK/SEND, END and POWER buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Using Clear Storage
If you can access the device settings, you can use Clear Storage to reset your device back to factory default settings.
1. Tap Start > Settings, and then tap All Settings.
2. On the System tab, tap Clear Storage.
3. Enter “1234” and then tap Yes.

AT&T Tilt hard reset

HTC AT&T Tilt soft reset

Resetting Your Device

Occasionally, you may need to reset your device. A soft (or normal) reset of your device clears all active program memory and shuts down all active programs. This can be useful when your device is running slower than normal, or a program is not performing properly. A soft reset is also necessary after the installation of some programs. If a soft reset is performed when programs are running, unsaved work will be lost.

To perform a soft reset

Use the stylus to press the RESET button found at the bottom of your device. Your device restarts and displays the Today screen.

AT&T Tilt hard reset

You can also perform a hard reset (also known as a full reset). A hard reset should be performed only if a normal reset does not solve a system problem. After a hard reset, the device is restored to its default settings - the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows Mobile® software and other pre-installed programs will remain.

Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, hard reset or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.

To perform a hard reset using device keys

1. Press and hold the left SOFT KEY and the right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom of your device.
2. Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:

3. Release the two SOFT KEYs, and then press the button on your device.
Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.

To perform a hard reset using Clear Storage

1. Tap Start > Settings > System tab > Clear Storage.
2. Type “1234” in the box and tap YES.

Audiovox 8615 hard reset

RESETTING THE Audiovox 8615 phone

To perform Verizon Audiovox 8615 hard reset

To reset the phone to its default settings:

1. Press Left SOFT key, 8 and 7 on dial pad  then enter “Password”.

Your Audiovox 8600 password is the last 4 digits of your phone number.

2. Press 7 for “Reset Phone”.

3. Read the message (It’ll be erase all data on your phone. Reset Phone?) then press [YES] or [NO].

When you select “Yes” you will see “Reset Phone! Your cellular telephone will reboot now” on the display and your cellular telephone will reset all settings to the factory defaults.

Audiovox 8930 hard reset

RESETTING THE Audiovox 8930 phone

To perform an Audiovox 8930 hard reset

RESET PHONE
Resetting the phone restores all the factory defaults, including the ringer types and display settings. The
internal Phone Book, Call History, Scheduler, and Messaging are unaffected.

1. Press LEFT SOFT key [MENU] 9, 6  then enter “Password”.
2. Press 8.
3. Read the message (It’ll be erase all data on your phone. Reset Phone?) then press [YES] Left SOFT key or [NO] Right SOFT key.

When you select “Yes” you will see “Reset Phone! Your Phone will reboot now” on the display and your cellular
telephone will reset all settings to the factory defaults.
NOTE: The default password is the last 4 digits of your phone number.
NOTE: As the data cannot be retrieved, the warning shall be marked.

Audiovox PPC-6800 hard reset

Resetting the PPC 6800

Warning! Your device will be set back to factory default settings. Please ensure any additional installed programs and/or user data have been backed up before a hard reset is performed.

To perform a hard reset
1. Press and hold the Left SOFT KEY and the Right SOFT KEY, and at the same time, use the stylus to press the RESET button at the bottom center part of your device.

2. Release the stylus, but continue pressing the two soft key buttons. Release them only when you see the following message on your device screen:

3. Slide open the hardware keyboard, then press R to do a hard reset.
4. When the restoration process is complete, press the Space Bar on the hardware keyboard to restart your device.

To perform a PPC-6800 soft reset:

Use the stylus to press the RESET button found at the bottom center part of your device. Your device restarts and displays the Today screen.

Audiovox 8910 hard reset

RESETTING THE Audiovox 8910 phone

To perform an Audiovox 8910 hard reset

Resetting the phone restores all the factory defaults, including the ringer types and display settings. The internal Phone Book, Call History, Scheduler, and Messaging are not affected.

1. Press Left SOFT key menu key 9 and 7 then enter “Password”.

Your Audiovox 8910 password is the last 4 digits of your phone number.

2. Press key 8 for “Reset Phone”.

3. Read the message (It’ll be erase all data on your phone. Reset Phone?) then press [YES] LEFT soft or [NO] right soft key.

When you select “Yes”, you will see “Wait a moment” on the display and the phone will power recycle.

When you select “Yes” you will see “Reset Phone! Your cellular telephone will reboot now” on the display and your cellular telephone will reset all settings to the factory defaults.

Audiovox 8600 hard reset

RESETTING THE Audiovox 8600 phone

To perform Verizon Audiovox 8600 hard reset

To reset the phone to its default settings:

1. Press Left SOFT key, 6 and 3 on dial pad  then enter “Password”.

Your Audiovox 8600 password is the last 4 digits of your phone number.

2. Press 4 for “Reset Phone”.

3. Select “Yes” or “No” with the navigation key. then press OK.

When you select “Yes,” “Wait a moment” appears and the phone will automatically reboot.

Audiovox 8500 hard reset

RESETTING THE Audiovox 8500 phone

To perform an Audiovox 8500 hard reset

To reset the phone to its default settings:

1. Press Left SOFT key, 5 and 3 on dial pad  then enter “Password”.

Your Audiovox 8450 password is the last 4 digits of your phone number.

2. Press 4 for “Reset Phone”.

3. Select “Yes” or “No” with the navigation key. then press OK.

When you select “Yes,” “Wait a moment” appears and the phone will return to Idle mode.

Audiovox 8450 hard reset

RESETTING THE Audiovox 8450 phone

To perform an Audiovox 8450 hard reset

To reset the phone to its default settings:

1. Press Left SOFT key menu key 8 and 3 then enter “Password”.

Your Audiovox 8450 password is the last 4 digits of your phone number.

2. Press key 5 for “Reset Phone”.

3. Select “Yes” or “No”, then press OK.

When you select “Yes”, you will see “Wait a moment” on the display and the phone will power recycle.

Audiovox Maestro PDA-1032 hard reset

Audiovox Maestro PDA-1032 hard reset

Press the power button while pressing and holding the reset switch with the stylus, and then release the power button. When a screen appears, release the reset switch. When initialization is completed, the Welcome screen appears. Set up the system as in the case of startup process.

Audiovox PPC-4100 hard reset

RESETTING THE Audiovox PPC-4100 HANDSET

You may have to perform a reset if the device freezes
(i.e., device no longer responds to the buttons on the
screen).
To perform a soft reset:
A soft reset allows your device to get a fresh start, similar to rebooting a computer. This will restart your
device and adjust memory allocation. All records and entries are retained after a soft reset. Unsaved data in
open programs may in some cases be lost.
1. Remove the stylus from its holder.
2. Lightly press the tip of the stylus to the reset button located on the rear panel of the device.

To perform an Audiovox PPC-4100 hard reset:

A hard reset will cut off power to your device. This will erase all records and entries, delete all programs you
have added, and restore the device default factory settings. Never perform a hard reset unless a soft reset
does not correct your problem. When you perform your next ActiveSync operation, you can restore any data that
you previously synchronized to your computer or you can restore data that you backed up to a storage card.

NOTE: When you perform a hard reset, the current date and time are not be retained. Formats, preferences, and other
settings are restored to their factory default settings.

1. Hold down the Power button on the front panel of your device.

2. While holding down the power button , gently press the tip of the stylus to the reset button.
The Confirmation message box appears.

3. Press the volume rocker key up.

Audiovox PPC-5050 hard reset

Resetting the Audiovox PPC-5050 Pocket PC Phone and Clearing Memory

You can perform a soft reset or a hard reset – a soft reset restarts your device and a hard reset switches the battery off. With a soft reset, some data may be lost in the programs that were open when the reset was performed. However, by performing a hard reset, all the data and new programs that you have added will be erased and the device will be restored to its factory setting – i.e. only programs installed at the factory will remain. With this in mind, it is important not to think about a hard reset as you would restarting, shutting down or even improperly switching off your desktop, but rather like a complete crash that requires you to erase your OS. Therefore, it is extremely important that you regularly back up data on your device to a SD card in the event you have to perform a hard reset.

Performing an Audiovox PPC-5050 soft reset:

If your Pocket PC Phone responds slowly, stops responding or freezes, try performing a soft reset. A soft reset causes the Pocket PC Phone to restart and re-adjust memory allocation. Unsaved data in open windows may be lost.
• Use the stylus to press and hold the Reset button.



1.Soft Reset. To reset the device, press the end of your stylus into the hole

4. Battery On/ Off Switch. To return the device to its original factory settings, simultaneously press here with the end of the top-half of your stylus and hold down the power button.
Battery Off will wipe all the data from your device

Performing an Audiovox PPC-5050 hard reset:

A hard device reset clears memory, deletes all data and restores the Pocket PC Phone to its default settings. Programs installed at the factory remain, while data you have created and programs you have installed are erased.


Unscrew the stylus and use the smaller point of the top-half.



Simultaneously press the battery switch and hold down the power switch to turn it off. Repeat to turn it back on.

Audiovox PPC-6600 hard reset

Resetting the PPC 6600 and

Clearing Memory
You can perform a soft reset or a full reset. During a soft
reset, the device is restarted and only some data in open
programs may be lost. However, a full reset turns the battery
off and returns the device to its original factory settings
and deletes all programs, files, contacts and other information
you have saved to the device. Therefore it is extremely
important to back up data to a storage card or your computer
on a regular basis in the event that a full reset has to be
performed.

To perform a soft reset:

If your PPC 6600 responds slowly, stops responding, or freezes,

try a soft reset. A soft reset causes the PPC 6600 to restart andre-adjust memory allocation. Unsaved data in open windows may be lost.

Use the stylus to press and hold the Reset button.

To perform a PPC6600 full reset:

A full device reset clears memory, deletes all data and restores
the PPC 6600 to its default settings. Programs installed at the
factory remain, while data you have created and programs you
have installed are all erased.
Press and hold the power button, and then the use
stylus to press the soft reset button at the same
time.
Be sure you have backed up all your data in a SD
card or in your PC before performing a full reset.

Audiovox PPC-6601 hard reset

Resetting the PPC 6601 and

Clearing Memory

You can perform a soft reset or a full reset. During a soft
reset, the device is restarted and only some data in open
programs may be lost. However, a full reset turns the battery
off and returns the device to its original factory settings
and deletes all programs, files, contacts and other information
you have saved to the device. Therefore it is extremely
important to back up data to a storage card or your computer
on a regular basis in the event that a full reset has to be
performed.

To perform a soft reset:
If your PPC 6601 responds slowly, stops responding, or freezes,
try a soft reset. A soft reset causes the PPC 6601 to restart and
re-adjust memory allocation. Unsaved data in open windows
may be lost.
Use the stylus to press and hold the Reset button.

To perform a full reset:

A full device reset clears memory, deletes all data and restores
the PPC 6601 to its default settings. Programs installed at the
factory remain, while data you have created and programs you
have installed are all erased.

Press and hold the power button, and then use the stylus to press the soft reset button at the same
time.
Be sure you have backed up all your data in a SD
card or in your PC before performing a full reset.

Audiovox PPC-6700 hard reset

Resetting Your Audiovox PPC-6700 Sprint PCS Vision Smart Device

To perform a soft reset:

Use the stylus to lightly press and hold the RESET button on the bottom of your PPC-6700. The device restarts, and then displays the Today screen.

Tip:To avoid data lost, please turn off your device before performing a soft reset.

To perform a hard reset:

1. Press and hold both SOFT KEYs on the device. Keep these keys pressed, and at the same time, use the stylus to lightly press and hold the RESET button on the bottom of your device.
2. Press either Y to restore to factory default, or N to exit the hard reset process.

Audiovox SMT-5600 hard reset

Audiovox SMT-5600 hard reset

Using buttons

1 Turn off the device.
2 Press and hold down the two soft keys.
3 Press the "Power" button on the top of the device and hold it down for 1.5 seconds. Release the soft keys when you see a message appear on the screen.
4 Press the "0" key to engage the hard reset.

Using Clear storage

Use the Clear Storage utility to reset all of your Smartphone's settings back to the manufacturer
default values, this will also erase all of your data.

Software Reset
1  Press "Start" > "Accessories" > "Clear Storage." Enter the password "1234" at the prompt and select the "Yes" button. The phone is reset to the factory default.

Audiovox Thera PDA2032 hard reset

Resetting Audiovox Thera PDA2032 (Soft reset)
Reset is equal to “Restart” on a computer. Reset only in unusual circumstances such as when the screen freezes and doesn’t respond to tapping. Information not saved prior to resetting will be deleted. When your device is reset, phone functions are ended.
To reset, press and release the Reset Switch while the power is on. Once reset, the Today screen appears.

When the power is on, press the Reset Switch with the stylus, then release. By doing so, reset is made and the Today screen appears.

Clearing Memory (Initialization)
Initializing the device returns it to the status when it was originally purchased. (Audiovox Thera PDA2032  Hard reset)

Note Initializing the device deletes all stored data, except built-in programs.
Before initialization, we recommend storing the memory data of the device into your computer or a storage card. Before initialization, remove a storage card.

To initialize:

1. Turn off the power.
2. Press the Power button while pressing and holding the Reset Switch with the stylus, then release the Power button.
3. Release the Reset Switch.

When initialization is complete, the welcome screen appears. Proceed with setup.

Audiovox XV6600 hard reset

Resetting the XV6600 and Clearing Memory

You can perform a soft reset or a full reset. During a soft reset, the device is restarted and only some data in open
programs may be lost. However, a full reset turns the battery off and returns the device to its original factory settings
and deletes all programs, files, contacts and other information you have saved to the device. Therefore it is extremely
important to back up data to a storage card or your computer on a regular basis in the event that a full reset has to be
performed.

To perform a soft reset:

If your XV6600 responds slowly, stops responding, or freezes, try a soft reset. A soft reset causes the XV6600 to restart and
re-adjust memory allocation. Unsaved data in open windows may be lost.
Use the stylus to press and hold the Reset button.

To perform a full reset:

A full device reset clears memory, deletes all data and restores the XV6600 to its default settings. Programs installed at the

factory remain, while data you have created and programs you have installed are all erased.

Press and hold the power button, and then the use stylus to press the soft reset button at the same

time.

Be sure you have backed up all your data in a SD card or in your PC before performing a full reset.

BenQ P30 hard reset

Resetting BenQ P30 phone

On the BenQ P30 phone keypad press *#9999# to reset default factory settings.

BenQ P31 hard reset

BenQ P31 hard reset

On the phone keypad press *#9999# to reset default factory settings.

See This way i hope solve your problem

BenQ P50 hard reset

BenQ P50 Soft reset

A soft reset restarts the PDA phone but does not erase any program data or system settings.
To perform a soft reset:

1. Locate the recessed Reset button at the bottom of the phone.
2. Insert the stylus into the recess to trigger the Reset button. Hold the Reset button down until the screen fades off.
3. Release the stylus from the Reset button to restart the phone.

BenQ P50 hard reset

A hard reset restarts the PDA phone and erases all program data and system settings. After a hard reset, your phone returns to its default settings and loses all information that is not recorded in ROM.
To perform a hard reset:

1. Locate the recessed Reset button at the bottom of the phone.
2. Press and hold down the Power button.
3. Without removing the Power button, insert the stylus into the recess to trigger the Reset button. Hold down both the Power button and the Reset button until the screen fades off.
4. When the screen has faded off completely, release both the Power button and the stylus.
5. You will notice the Power indicator light up green, at this point, press the Power button to turn ON the PDA phone.

BenQ P51 hard reset

BenQ P51 Soft reset

A soft reset restarts the PDA phone but does not erase any data, program, or system settings.

To perform a soft reset:

1. Locate the recessed Reset (7) at the bottom of the phone.
2. Insert the stylus into the recess to trigger Reset. Hold Reset down until the screen fades off.
3. Release the stylus from the Reset button to restart the phone.



7Reset button Insert the stylus in to the recess to trigger the reset button.

BenQ P51 Hard reset

As with a soft reset, a hard reset restarts the PDA phone without erasing any data, program, or system settings. But a hard reset also resets the system time to the default value (1 January, 2006).

To perform a hard reset:

1. Locate the recessed Reset at the bottom of the phone.
2. Press and hold down Power button.
3. Without releasing Power, insert the stylus into the recess to trigger Reset. Hold down both Power and Reset until the screen fades off.
4. When the screen has faded off completely, release both Power and the stylus.

1 Power button

- Press to power off or on (entering or leaving the sleep mode).
- Long press to turn the backlight off or on (consuming more power than the sleep mode).

BenQ P51 Clean boot

A clean boot restarts the PDA phone by erasing all data and programs as well as system settings, and thus returns to its factory default state.

To perform a clean reset:

1. Locate the recessed Reset at the bottom of the PDA phone.
2. Press and hold down Power (1).
3. Without releasing Power, insert the stylus into the recess to trigger Reset. Hold down both Power and Reset until the screen fades off.
4. When the screen has faded off completely, release both Power and the stylus.
5. Long press Send.
6. Press Y to confirm the clean boot.