Yakumo deltaX GPS hard reset

Resetting Your Yakumo deltaX GPS

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Yakumo deltaX GPS is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo deltaX GPS; for example, you should reset:
After you restore data from your desktop computer.
When your Yakumo deltaX GPS stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Yakumo deltaX GPS:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Yakumo deltaX GPS.

Yakumo deltaX GPS hard reset

Restoring Factory Default State

In some cases, you may need to restore your Yakumo deltaX GPS to the factory default state by clearing the memory (RAM) from your Yakumo deltaX GPS.
For example, you should clear the memory:
When your Yakumo deltaX GPS does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased. (Programs installed to ROM at the factory are not affected.)
CAUTION:
To ensure the integrity of your data should it be necessary to clear the memory, you’re advised to regularly back up your data.
Do not slide the ON/OFF Switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo deltaX GPS:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo deltaX GPS.
3. Stop all running programs by tapping Start  > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF (up) position.

5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Yakumo deltaX GPS will automatically turn on and prompt you to start the setup wizard.

7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.

9. You may also want to restore data to your Yakumo deltaX GPS from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo omikron BT hard reset

Yakumo Omikron BT Reboot

Warm-boot (Reset): Use the tip of the stylus to press down the “Reset” button located on the left side of the Pocket PC.

Yakumo Omikron BT hard reset Cold-boot:

Use one finger to press and hold the “Power” button on the top of the Pocket PC, meanwhile, use the tip of the stylus to press down the
“Reset” button located on the left side of the Pocket PC. Then release the “Power” button and the “Reset” button simultaneously. After rebooting,
follow the instructions on the screen to finish screen alignment…etc, tasks.

Yakumo alpha GPS hard reset

Yakumo alpha GPS Hard reset Soft reset

Resetting Your Yakumo alpha GPS

Caution: Resetting will cause unsaved data to be lost.

Resetting your Yakumo alpha GPS is similar to restarting your desktop computer.
It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo alpha GPS; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo alpha GPS stops responding; in other words, it appears to be frozen or locked up.

Follow this procedure to reset your Yakumo alpha GPS:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the soft reset switch (position 1, see figure).

Remove the SD/MMC card (if installed).
In some cases, you may need to restore your Yakumo alpha GPS to the factory default state by clearing the memory (RAM) from your Yakumo alpha GPS. For example, you should clear the memory:

• When your Yakumo alpha GPS does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased. (Programs installed to ROM at the factory are not affected.)

Caution:
To ensure the integrity of your data should it be necessary to clear the memory, you are advised to regularly synchronize your data (via ActiveSync) with your desktop computer or back up (with a backup utility) to a storage card. For more information on
backing up data, see section 3.5.
Do not slide the battery switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo alpha GPS:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo alpha GPS.
3. Stop all running programs by tapping Settings - System tab - Memory icon - Running Programs tab - Stop All.

4. Use the stylus to slide the battery switch to the left (OFF position).

5. Wait for 1 minute and then slide the switch again to the right (ON position).

6. Your Yakumo alpha GPS will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a partnership with your desktop computer.
9. You may also want to restore data to your Yakumo alpha GPS from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as when you restore the factory default state.

Yakumo alphaX GPS hard reset

Resetting Your Yakumo AlphaX GPS

Caution: Resetting will cause unsaved data to be lost.

Resetting your Yakumo AlphaX GPS is similar to restarting your desktop computer.
It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo AlphaX GPS; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo AlphaX GPS stops responding; in other words, it appears to be frozen or locked up.

Follow this procedure to reset your Yakumo alpha
GPS:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the soft reset switch
(position 1, see figure).

Remove the SD/MMC card (if installed).
In some cases, you may need to restore your Yakumo AlphaX GPS to the factory default state by clearing the memory (RAM) from your Yakumo alpha GPS. For example, you should clear the memory:

• When your Yakumo AlphaX GPS does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased. (Programs installed to ROM at the factory are not affected.)

Caution:
To ensure the integrity of your data should it be necessary to clear the memory, you’re advised to regularly synchronize your data (via ActiveSync) with your desktop computer or back up (with a backup utility) to a storage card. For more information on
backing up data, see section 3.5.
Do not slide the battery switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo AlphaX GPS:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter,
from your Yakumo AlphaX GPS.

3. Stop all running programs by tapping Settings - System tab - Memory icon - Running Programs tab - Stop All.


4. Use the stylus to slide the battery switch to the left (OFF position).

5. Wait for 1 minute and then slide the switch again to the right (ON position).

6. Your Yakumo AlphaX GPS will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a partnership with your desktop computer.
9. You may also want to restore data to your Yakumo AlphaX GPS from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as when you restore the factory default state.

Yakumo delta hard reset

Follow this procedure to clear the memory from your Yakumo delta 200:

1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo delta 200.
3. Stop all running programs by tapping  Settings - System tab - Memory icon - Running Programs tab - Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Yakumo delta will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Yakumo delta from your most recent backup file.

NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo delta 300 hard reset

Yakumo Delta 300 Soft reset

Resetting Your Yakumo delta 300

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Yakumo delta 300 is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo delta 300; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo delta 300 stops responding; in other words, it appears to be “frozen” or “locked up.”

Follow this procedure to reset your Yakumo delta 300:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Yakumo delta 300.

Yakumo Delta 300 Hard reset

Restoring Factory Default State

In some cases, you may need to restore your Yakumo delta 300 to the factory default state by clearing the memory (RAM) from your Yakumo delta 300. For example, you should clear the memory:

• When your Yakumo delta 300 does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.

(Programs installed to ROM at the factory are not affected.)

CAUTION:
To ensure the integrity of your data should it be necessary to clear the memory, you’re advised to regularly back up your data.
Do not slide the ON/OFF Switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo delta 300:

1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo delta 300.
3. Stop all running programs by tapping  Settings - System tab - Memory icon - Running Programs tab - Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Yakumo delta 300 will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Yakumo delta 300 from your most recent backup file.

NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo delta 300 GPS hard reset

Yakumo Delta 300 GPS Soft reset

Resetting Your Yakumo delta 300 GPS

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Yakumo delta 300 GPS is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo delta 300 GPS; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo delta 300 GPS stops responding; in other words, it appears to be frozen or locked up.

Follow this procedure to reset your Yakumo delta 300 GPS:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Yakumo delta 300 GPS.

Yakumo Delta 300 GPS Hard reset

Restoring Factory Default State

In some cases, you may need to restore your Yakumo delta 300 GPS to the factory default state by clearing the memory (RAM) from your Yakumo delta 300 GPS. For example, you should clear the memory:

• When your Yakumo delta 300 GPS does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

CAUTION:
To ensure the integrity of your data should it be necessary to clear the memory, you are advised to regularly back up your data.
Do not slide the ON/OFF Switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo delta 300 GPS:

1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo delta 300 GPS.
3. Stop all running programs by tapping Settings - System tab - Memory icon - Running Programs tab - Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Yakumo delta 300 GPS will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Yakumo delta 300 GPS from your most recent backup file.

NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo delta 300 GPS 2L hard reset

Resetting Your Yakumo delta 300 GPS 2L

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Yakumo delta 300 GPS 2L is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo delta 300 GPS 2L; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo delta 300 GPS 2L stops responding; in other words, it appears to be “frozen” or “locked up.”

Follow this procedure to reset your Yakumo delta 300 GPS 2L:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Yakumo delta 300 GPS 2L.

Yakumo Delta 300 GPS 2L Hard reset

Restoring Factory Default State

In some cases, you may need to restore your Yakumo delta 300 GPS 2L to the factory default state by clearing the memory (RAM) from your Yakumo delta 300 GPS 2L. For example, you should clear the memory:

• When your Yakumo delta 300 GPS 2L does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

CAUTION:
To ensure the integrity of your data should it be necessary to clear the memory, you’re advised to regularly back up your data.
Do not slide the ON/OFF Switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo delta 300 GPS 2L:

1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo delta 300 GPS 2L.
3. Stop all running programs by tapping  Settings - System tab - Memory icon - Running Programs tab - Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Yakumo delta 300 GPS 2L will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Yakumo delta 300 GPS 2L from your most recent backup file.

NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo delta 400 hard reset

Yakumo Delta 400 Soft reset

Resetting Your Yakumo delta 400

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Yakumo delta 400 is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo delta 400; for example, you should reset:

• After you restore data from your desktop computer.

• When your Yakumo delta 400 stops responding; in other words, it appears to be “frozen” or “locked up.”

Follow this procedure to reset your Yakumo delta 400:

1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Yakumo delta 400.

Yakumo Delta 400 Hard reset

Restoring Factory Default State

In some cases, you may need to restore your Yakumo delta 400 to the factory default state by clearing the memory (RAM) from your Yakumo delta 400. For example, you should clear the memory:

• When your Yakumo delta 400 does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.

(Programs installed to ROM at the factory are not affected.)

CAUTION:
To ensure the integrity of your data should it be necessary to clear the memory, you’re advised to regularly back up your data.
Do not slide the ON/OFF Switch unless it is necessary.

Follow this procedure to clear the memory from your Yakumo delta 400:

1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Yakumo delta 400.
3. Stop all running programs by tapping Settings - System tab - Memory icon - Running Programs tab - Stop All.
4. Use the stylus to slide the ON/OFF switch to the OFF position.
5. Wait for 1 minute and then slide the switch back to the ON position.
6. Your Yakumo delta 400 will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.
8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Yakumo delta 400 from your most recent backup file.

NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

Yakumo deltaX 5 BT hard reset

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Yakumo deltaX 5 BT is similar to restarting your desktop
computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Yakumo deltaX 5 BT; for example, you should reset:

• After you restore data from your desktop computer.
• When your Yakumo deltaX 5 BT stops responding; in other words, it appears to be “frozen” or “locked up.”

Use the stylus to press the reset button on your Yakumo deltaX 5 BT.

Restoring Last State

Follow this procedure to restore your Yakumo deltaX 5 BT to the last state when your Yakumo deltaX 5 BT does not respond after being reset.

1. Disconnect all cables, including the AC adapter, from your Yakumo deltaX 5 BT.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position.
4. Your Yakumo deltaX 5 BT turns on.

NOTE: You need to restore your Yakumo deltaX 5 BT to factory default state if you have set up a password but forget it.

SysInfoSysInfo provides the following functions:

• Restore your device to the factory default state.
• Automatically lock your device when it turns off.

Tap Settings System SysInfo. The tool consists of these tabs: System, Clean Boot, and AutoLock. They are described as below.

System
This screen displays the system information.

Clean Boot  -  Hard resetUse this function if you want to restore your Yakumo deltaX 5 BT to the factory default state. Restoring factory default state means all data you have entered in RAM, including all files, system settings, and additional programs you have installed, will be erased.

AutoLock
You may not want any accidental touching of the buttons to turn on your device. This can happen when, for example, you put your device in a bag and something else in the bag presses against your device.

This AutoLock feature allows your device to be automatically locked whenever it turns off. Even if your device is accidentally turned on, a message will prompt you to unlock it within 5 seconds. As long as there is no response from you within 5 seconds, the device turns off again. This helps saving battery power