Casio BE-300 hard reset

Full Reset Casio BE300

- While holding down the [Power] button, use the stylus to press the [Reset] button.

- This displays the initialization startup screen. After a short while, the touch screen calibration screen appears

- Follow the instructions that appear on the screen to set up your CASSIOPEIA.

- The Top Menu appears on the screen after setup is complete.

Resetting your CASSIOPEIA is the same as restarting your computer. Performing a
reset causes any data you are working on but have not saved yet to be lost, but data
saved in memory and other settings are basically left unchanged.
You should perform the reset operation whenever your CASSIOPEIA behaves
abnormally due to operational error or some other problem. The reset operation is
required in the following cases.
- When there is no response when you tap the screen or press a button
- When the icon that indicates some operation is in progress continues to rotate on the
screen for a long time

Check to make sure the battrery icon is not in the system tray before you press the reset button.

Performing the reset operation causes all user files and folders that are not contained
in the My Device\Nand Disk folder to be deleted. To keep a file or folder from being
deleted by the reset operation, store it in the My Device\Nand Disk folder or on a
storage card.

Though saved data is normally not lost when you perform a reset operation, abnormal
data in memory can cause all saved data to be cleared. Because of this, you should
always back up data to a storage card whenever possible before performing a reset
operation.

To reset your CASSIOPEIA
1. Turn on your CASSIOPEIA.
2. Use the stylus to press the [Reset] button.

3. The message "Starting..." appears on the display to let you know that the reset operation is starting.

The Top Menu should appear on the display after a short while. Since this procedure does not affect data and settings stored in memory, you can now continue using the CASSIOPEIA.

What to do if resetting does not solve the problem
Perform the following steps if resetting the CASSIOPEIA does not restore normal operation.
1. While holding down the [Power] button, use the stylus to press the [Reset] button.
This displays the initialization startup screen.
2. The message "Starting..." appears on the display to let you know that the reset operation is starting.
The Top Menu should appear on the display after a short while. Since this procedure does not affect data and settings stored in memory, you can now continue using the CASSIOPEIA.

Casio BE 300 SAFE mode

1. Connect the AC adapter to the CASSIOPEIA.
2. Press the [Power] button.
3. While holding down the [OK] button, use the stylus to press the [Reset] button.
This enters the Safe Mode.

4. Tap OK button.

This displays the touch screen calibration screen. Follow the instructions on the display to calibrate the touch screen.
The following screen appears after you finish touch screen calibration.

Casio PV-100 hard reset

Resetting the PV 100 Unit

Warning!
The following procedure erases all data stored in the memory of the PV Unit.
Perform this operation only when you want to delete all data and initialize the
settings of the PV Unit.
Remember - you should always keep copies of important data by writing it down,
or by transferring it to a personal computer.
To reset the PV Unit

1. Open the cover and touch the screen with the stylus to turn on power.
2. Use the stylus to press the RESET button on the back of the PV Unit.

• If the above does not appear on the display when you press the RESET
button, slide the battery switch to the REPLACE BATTERIES position
and remove the battery compartment cover. Use the stylus to press the P
button and then replace the battery compartment cover. Slide the battery
switch back to the NORMAL OPERATION position and then press the
RESET button.
3. Tap the center of each of the four cross marks as they appear on the
screen.
• The contrast adjustment screen appears next.
4. Tap  to adjust the contrast of the display, and then tap OK.

5. In response to the message that appears, tap Yes to reset the PV Unit and
clear all memory contents, or No to abort the reset procedure without
doing anything.
6. If you tapped Yes in the above step, a second confirmation message
appears. Tap Yes to reset the PV Unit and clear all memory contents, or
No to abort the reset procedure without doing anything.
• Tapping Yes in the above step starts the actual reset procedure.
7. After the reset procedure is complete, tap the button next to the language
you want to select as the system language.
8. Tap Set to change to the pop up tool screen.

9. Check the time setting and correct it if necessary .
• Following are the initial settings of the PV Unit after you perform the
RESET operation.
Main clock: Clock 1
London
Jan/1/1999
12:00 am
12-hour format
Clock 2: New York
Daily Alarm: 12:00 pm
Sound: Daily Alarm off, all others on
Character input: CAPS off

Casio A-11 hard reset

Resetting the A-11

Casio A-11 Normal Reset

You should reset the A-11 whenever you suspect some external abnormality as caused it to malfunction.
Performing tie reset operation when the A-11 is hung up or experi-encing other operational problems but no corruption of memory contents resets the A-11 without affecting memory contents or settings. A normal reset causes the Desktop to appear on the screen.

Casio A-11 Memory Reset

Performing the reset operation after memory data has been corrupted clears memoiy contents and settings, and causes the welcome wizard screen to appear. Set up the A-11 in accordance with the on-screen guidance.

To reset the A-11
1. Press the power switch to turn on the A- 11.
2. Use the stylus to press the reset button.


This causes the A-11 to turn off.

Always use the stylus that comes with the A-11 whenever performing any touch screen operation. Using any other object can result in damage to and malfunction of the A-11.
3. Turn the A-11 back on to resume the reset operation.

Initializing the A-11

Caution! The following operation deletes all data stored in memory.
1. Remove both the main and back-up batteries.
2. Wait for about five minutes.
3. First install the main batteries.
• Be sure to install the main batteries first. If you install the back-up battery first, the unit will not start up correctly. If you have trouble starting up after performing this procedure, repeat the procedure from step 1 again.
4. Slide the release (both buttons) of the main battery holder towards "NORMAL OPERATION".
5. Wait for about five seconds, arid then turn on power.
6. Perform the settings in accordance with the welcome wizard menu that appears on the screen.
7. After the settings turn power off.
8. Install the back-up battery. After completing the Initialization, you can re-install any data you previously backed up.

Casio PV-200 hard reset

Resetting the PV 200 Unit

Warning!
The following procedure erases all data stored in the memory of the PV Unit.
Perform this operation only when you want to delete all data and initialize the
settings of the PV Unit.
Remember - you should always keep copies of important data by writing it down,
or by transferring it to a personal computer.
To reset the PV Unit

1. Open the cover and touch the screen with the stylus to turn on power.
2. Use the stylus to press the RESET button on the back of the PV Unit.

• If the above does not appear on the display when you press the RESET
button, slide the battery switch to the REPLACE BATTERIES position
and remove the battery compartment cover. Use the stylus to press the P
button and then replace the battery compartment cover. Slide the battery
switch back to the NORMAL OPERATION position and then press the
RESET button.
3. Tap the center of each of the four cross marks as they appear on the
screen.
• The contrast adjustment screen appears next.
4. Tap  to adjust the contrast of the display, and then tap OK.

5. In response to the message that appears, tap Yes to reset the PV Unit and
clear all memory contents, or No to abort the reset procedure without
doing anything.
6. If you tapped Yes in the above step, a second confirmation message
appears. Tap Yes to reset the PV Unit and clear all memory contents, or
No to abort the reset procedure without doing anything.
• Tapping Yes in the above step starts the actual reset procedure.
7. After the reset procedure is complete, tap the button next to the language
you want to select as the system language.
8. Tap Set to change to the pop up tool screen.

9. Check the time setting and correct it if necessary .
• Following are the initial settings of the PV Unit after you perform the
RESET operation.
Main clock: Clock 1
London
Jan/1/1999
12:00 am
12-hour format
Clock 2: New York
Daily Alarm: 12:00 pm
Sound: Daily Alarm off, all others on
Character input: CAPS off

Casio A-10 Normal Reset

Casio A-10 Normal Reset

You should reset the A-10 whenever you suspect some external abnormality as caused it to malfunction.
Performing tie reset operation when the A-10 is hung up or experi-encing other operational problems but no corruption of memory contents resets the A-10 without affecting memory contents or settings. A normal reset causes the Desktop to appear on the screen.

Casio A-10 Memory Reset

Performing the reset operation after memory data has been corrupted clears memoiy contents and settings, and causes the welcome wizard screen to appear. Set up the A-10 in accordance with the on-screen guidance.

To reset the A-10
1. Press the power switch to turn on the A- 11.
2. Use the stylus to press the reset button.


This causes the A-10 to turn off.

Always use the stylus that comes with the A-10 whenever performing any touch screen operation. Using any other object can result in damage to and malfunction of the A-10.
3. Turn the A-10 back on to resume the reset operation.

Initializing the A-10

Caution! The following operation deletes all data stored in memory.
1. Remove both the main and back-up batteries.
2. Wait for about five minutes.
3. First install the main batteries.
• Be sure to install the main batteries first. If you install the back-up battery first, the unit will not start up correctly. If you have trouble starting up after performing this procedure, repeat the procedure from step 1 again.
4. Slide the release (both buttons) of the main battery holder towards "NORMAL OPERATION".
5. Wait for about five seconds, arid then turn on power.
6. Perform the settings in accordance with the welcome wizard menu that appears on the screen.
7. After the settings turn power off.
8. Install the back-up battery. After completing the Initialization, you can re-install any data you previously backed up.

Casio A-20 hard reset

Casio A-20 hard reset and soft reset

Soft Reset
You should reset the CASSIOPEIA whenever it stops working or whenever some other operational problem has caused it to malfunction.

To reset the CASSIOPEIA A20
1. Press the RESET button with the stylus.
• This automatically turns off CASSIOPEIA power.



2. Press the power switch to turn on power and start the reset process.

What happens next depends on memory status.

Case A: Memory Contents Not Corrupted

In this case, the display changes in the sequence shown below.

Start up screen  Normal Desktop
Normal operation is restored after the desktop appears, with all memory contents and settings unchanged.

Full Reset
Perform the full reset when you want to clear all memory contents and settings because memory contents are corrupted, because you have forgotten the security code, or for any other reason.
Important • The following procedure deletes all data in memory. Be sure to save any important data contents you may need later to a computer disk or other medium. Always keep separate back-up copies of important data.

To perform a Casio A20 full reset
1. While holding down the [Ctrl] key and the [Alt] key, press the RESET button.


2. The message "All memory contents will be deleted! Touch the screen to continue..." appears on the display.
• If you don't want to perform a full reset, press the RESET button. This performs the normal reset, which does not clear memory contents.

Casio A-21 hard reset

Casio A-21 hard reset and soft reset

Soft Reset
You should reset the CASSIOPEIA whenever it stops working or whenever some other operational problem has caused it to malfunction.

To reset the CASSIOPEIA A21
1. Press the RESET button with the stylus.
• This automatically turns off CASSIOPEIA power.



2. Press the power switch to turn on power and start the reset process.

What happens next depends on memory status.

Case A: Memory Contents Not Corrupted

In this case, the display changes in the sequence shown below.

Start up screen  Normal Desktop
Normal operation is restored after the desktop appears, with all memory contents and settings unchanged.

Full Reset
Perform the full reset when you want to clear all memory contents and settings because memory contents are corrupted, because you have forgotten the security code, or for any other reason.
Important • The following procedure deletes all data in memory. Be sure to save any important data contents you may need later to a computer disk or other medium. Always keep separate back-up copies of important data.

To perform a Casio A20 full reset
1. While holding down the [Ctrl] key and the [Alt] key, press the RESET button.


2. The message "All memory contents will be deleted! Touch the screen to continue..." appears on the display.
• If you don't want to perform a full reset, press the RESET button. This performs the normal reset, which does not clear memory contents.

Casio E-10 hard reset

Resetting the Casio E-10 Unit

"Reset" is similar to a computer reboot. Performing a reset deletes any data that is in the process of being input or edited, without yet being saved. Data stored in memory and all settings, however, are retained.
Perform the reset opeation whenever the unit fails to operate correctly due to operational error or some other abnormality. Any of the following symptoms indicate that reset is required.
• Failure of the unit is respond when the screen is tapped or a button is pressed
• The hourglass icon remaining on the screen

Performing a Reset

Use the stylus to press the RESET button.
• The unit performs a reset followed by a memory check operation
If no data error is found, the following two screens appear on the display in succession.
• Startup Screen
• Desktop
2. Normal unit operation is possible after the desktop appears.
• Since memory data and settings are retained, you can continue operation from where you last left off.
Important If the above operation does not solve the problem, perform a Casio E10 full reset.

Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: "A problem with memory contents has been found..."

Performing a Casio E-10 Full Reset

Important
• The following procedure deletes all data in memory. Be sure that data is backed up or that you no longer need it before performing the following procedure.
• If there is a CompactFlash card in the CASSIOPEIA's slot, remove the card before performing the full reset.
1. Make sure that unit power is turned On.
2. While holding down the 'Power' button, use the stylus to hold down the RESET button for about two seconds.
• This causes the following message to appear on the display screen. "Proceeding with this operation initializes memory. Press [Action] to proceed or I [Exit] to cancel."

3. Press the [Action] control.
• This causes the following message to appear on the display screen.
"Proceeding with this operation deletes all data stored in memory. Press [Action] to proceed or [Exit] to cancel."
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen.

You can abort the full reset operation while the messages in steps 2 and 3 are on the display by pressing the [Exit] button.

Errors Following a Full Reset

Either of the following two conditions can cause errors to continue, even after you perform a full reset.
• Hardware detect
• System problem caused by failure by you to correctly perform the reset procedure before using the unit for the first time

If you suspect that the problem is being caused because you did not properly reset the unit before using it for the first time, perform the following procedure.
This should correct the problem.

• Perform the following procedure if your CASSIOPEIA remains locked up even at you perform a full reset.
Important 
• The following operation deletes all data in CASSIOPEIA memory.
• If you previously backed up your CASSIOPIA data to your desktop computer hard disk or a CompactFlash memory card, you will be able to restore the data after performing the following operation.
• If backed up data includes data that is the cause of the original problem, your CASSIOPEIA may start malfunctioning again after data is resumed. In this case, you Will not be able to use the backed up data.
• To protect against backing up corrupted data that can cause problems when restored, first synchronize Pocket Outlook program data between your CASSIOPEIA and desktop computer. Next, use drag and drop to copy other files to you computer.

1. Remove both the main batteries and the back-up battery from the CASSIOPEIA.
2. Wait for about five minutes.
3. Reload the main batteries.
• Be sure to load the main batteries first. The CASSIOPEIA will not Operate properly if you load the back-up battery first. If you inadvertently load the back-up battery first, start over from step 1. above.
4. Reload the back-up battery.
5. Replace the battery cover and slide the battery cover lock to LOCK.
6. Wait for about five seconds and then press the [Power] button to turn on your CASSIOPEIA. • Turning on power displays the startup screen, following by the touch panel calibration screen.
7. Fllow the instructions that appear on the screen to make initial settings.
8. Alter setting up your CASSIOPEIA, turn it off.
• After completing the above procedure, you can restore ditit you have backed up on your desktop computer hard disk or CompactFlash memory card. See the separate Palm-size PC User's Guide for information about restoring backed up data.

Casio E-100 hard reset

Full Reset Casio E100 (Memory Initialize)

Full reset (memory initialize) deletes all data, and resets all unit parameters to their
initial defaults.
The following are conditions when you should perform a full reset.
· When you want to delete all memory data and return unit settings to their factory
defaults
· When you forget your password and need to clear it
· When a data error causes operational problems
· Appearance of the message: “A problem with memory contents has been found...”
Performing a Full Reset
Important
· The following procedure deletes all data in memory. Be sure that data is backed up or
that you no longer need it before performing the following procedure.
· If there is a CompactFlash card in the CASSIOPEIA’s slot, remove the card before
performing the full reset.
1.Make sure that unit power is turned on.
2. While holding down the [Power] button, use the stylus to hold down the RESET
button for about two seconds.
· This causes the following message to appear on the display screen.
“Proceeding with this operation initializes memory. Press [Action] to proceed or
[Exit] to cancel.”
3. Press the [Action] control.
· This causes the following message to appear on the display screen.
“Proceeding with this operation deletes all data stored in memory. Press [Action]
to proceed or [Exit] to cancel.”
4. Press the [Action] control again.

This starts the full reset operation, which deletes all data in memory.
· Pressing the [Action] control displays the Startup screen.
You can abort the full reset operation while the messages in steps 2 and 3 are on the
display by pressing the [Exit] button.

Errors Following a Full Reset

Either of the following two conditions can cause errors to continue, even after you
perform a full reset.
· Hardware defect
· System problem caused by failure by you to correctly perform the reset procedure
before using the unit for the first time

1.Remove both the main battery and the backup battery from the CASSIOPEIA.
2.Wait for about five minutes.
3. Reload the main battery.
· Be sure to load the main battery first. The CASSIOPEIA will not operate properly if
you load the backup battery first. If you inadvertently load the backup battery first,
start over from step 1 above.
4. Attach the AC adapter and charge the battery pack.
5. Reload the backup battery.
6.Make sure the battery cover switch is in the LOCK position.
7.Wait for about five seconds and then press the [Power] button to turn on your
CASSIOPEIA.
· Turning on power displays the startup screen, following by the touch panel
calibration screen.
8. Follow the instructions that appear on the screen to make initial settings.
9. After setting up your CASSIOPEIA, turn it off.

After completing the above procedure, you can restore data you have backed up on
your desktop computer hard disk or CompactFlash memory card.

Replacing the Casio E100 Backup Battery

Important
· Never remove the main battery and backup battery from the CASSIOPEIA at the
same time. Doing so causes all data stored in memory to be deleted.
· Should the main battery and the backup battery both require replacement, be sure to
always replace the main battery first.
· Be sure to replace the backup battery as soon as possible whenever the following
message appears on the display: “Prevent possible data loss by promptly replacing
or recharging your back up battery according to your hardware manufacturer’s
instructions.”

1.Make sure your CASSIOPEIA is turned off.
· Press the [Power] button to turn off power.
2.Turn the CASSIOPEIA over.
3. Slide the battery cover switch to BACK UP, and then remove the backup battery
cover.

4.Remove the old battery.
5.Wipe off a new lithium battery (CR2032) with a dry cloth, and load it into the
CASSIOPEIA.

Make sure the positive side is facing up, so you can see it.
6. Replace the backup battery cover.
7. Slide the battery cover switch back to LOCK.

Casio IT300 hard reset

Full Reset Casio IT300 and Soft reset

Resetting the Handheld Terminal
Resetting the terminal is the same as resetting a PC. Performing a reset causes all unsaved RAM data to be lost that are in mid-course of inputting and editing, but data and settings that are already stored in the FlashROM should be unaffected. Perform a reset to restore normal operation whenever the Handheld Terminal operates abnormally due to misoperation or some other reason.

Casio IT300 Soft reset

Use a pointed implement such as a mechanical pencil (with the lead retracted) to press the reset switch on the back of the terminal. This starts the reset operation.
* Do not use a toothpick or pencil or other sharp object whose tip may break off the reset switch.

Casio IT300 hard reset

Performing a Full Reset (Initialization) Performing, a full reset deletes all data and resets various settings to their defaults. *Data stored in the Flashdisk folder remain unaffected.
Perform a full reset whenever any one of the following,- conditions exists.

• When you want to delete installed programs and settings, and resume the terminal to the initial condition.

• When you are no longer able to use the Handheld Terminal because you forgot your password.

• When the Handheld Terminal does not operate normally due to a memory problem.

Important! Performing a full reset resets all data to their defaults except stored in the Flashdisk folder. If possible, backup data of the terminal to a PC or to the Flashdisk folder. The reset procedure and display message appeared on performing the reset is according to the model you operate.

1. While holding down the Fn key and CLR key. push down the reset switch for about 3 seconds with the tip of a pointed implement such as a mechanical pencil until the message shown below appears on the display.

• To cancel the full reset operation. press the MENU key.

2. Press the Trigger key. This causes the message shown below to appear.

• To cancel the full reset operation. press the MENU key.

3. Press the Trigger key again to perform the full reset.

• The full reset starts and all data in the memory are erased. and the start-up screen appears.

Data stored in the Flashdisk folder remain unaffected.

Casio E-105 hard reset

Full Reset Casio E105 (Memory Initialize)

Full reset (memory initialize) deletes all data, and resets all unit parameters to their
initial defaults.
The following are conditions when you should perform a full reset.
· When you want to delete all memory data and return unit settings to their factory
defaults
· When you forget your password and need to clear it
· When a data error causes operational problems
· Appearance of the message: “A problem with memory contents has been found...”
Performing a Full Reset
Important
· The following procedure deletes all data in memory. Be sure that data is backed up or
that you no longer need it before performing the following procedure.
· If there is a CompactFlash card in the CASSIOPEIA’s slot, remove the card before
performing the full reset.
1.Make sure that unit power is turned on.
2. While holding down the [Power] button, use the stylus to hold down the RESET
button for about two seconds.
· This causes the following message to appear on the display screen.
“Proceeding with this operation initializes memory. Press [Action] to proceed or
[Exit] to cancel.”
3. Press the [Action] control.
· This causes the following message to appear on the display screen.
“Proceeding with this operation deletes all data stored in memory. Press [Action]
to proceed or [Exit] to cancel.”
4. Press the [Action] control again.

This starts the full reset operation, which deletes all data in memory.
· Pressing the [Action] control displays the Startup screen.
You can abort the full reset operation while the messages in steps 2 and 3 are on the
display by pressing the [Exit] button.

Errors Following a Casio E105 Full Reset

Either of the following two conditions can cause errors to continue, even after you
perform a full reset.
· Hardware defect
· System problem caused by failure by you to correctly perform the reset procedure
before using the unit for the first time

1.Remove both the main battery and the backup battery from the CASSIOPEIA.
2.Wait for about five minutes.
3. Reload the main battery.
· Be sure to load the main battery first. The CASSIOPEIA will not operate properly if
you load the backup battery first. If you inadvertently load the backup battery first,
start over from step 1 above.
4. Attach the AC adapter and charge the battery pack.
5. Reload the backup battery.
6.Make sure the battery cover switch is in the LOCK position.
7.Wait for about five seconds and then press the [Power] button to turn on your
CASSIOPEIA.
· Turning on power displays the startup screen, following by the touch panel
calibration screen.
8. Follow the instructions that appear on the screen to make initial settings.
9. After setting up your CASSIOPEIA, turn it off.

After completing the above procedure, you can restore data you have backed up on
your desktop computer hard disk or CompactFlash memory card.

Replacing the Casio E105 Backup Battery

Important
· Never remove the main battery and backup battery from the CASSIOPEIA at the
same time. Doing so causes all data stored in memory to be deleted.
· Should the main battery and the backup battery both require replacement, be sure to
always replace the main battery first.
· Be sure to replace the backup battery as soon as possible whenever the following
message appears on the display: “Prevent possible data loss by promptly replacing
or recharging your back up battery according to your hardware manufacturer’s
instructions.”

1.Make sure your CASSIOPEIA is turned off.
· Press the [Power] button to turn off power.
2.Turn the CASSIOPEIA over.
3. Slide the battery cover switch to BACK UP, and then remove the backup battery
cover.

4.Remove the old battery.
5.Wipe off a new lithium battery (CR2032) with a dry cloth, and load it into the
CASSIOPEIA.

Make sure the positive side is facing up, so you can see it.
6. Replace the backup battery cover.
7. Slide the battery cover switch back to LOCK.

Casio E-11 hard reset

Resetting the Casio E-11 Unit

"Reset" is similar to a computer reboot. Performing a reset deletes any data that is in the process of being input or edited, without yet being saved. Data stored in memory and all settings, however, are retained.
Perform the reset opeation whenever the unit fails to operate correctly due to operational error or some other abnormality. Any of the following symptoms indicate that reset is required.
• Failure of the unit is respond when the screen is tapped or a button is pressed
• The hourglass icon remaining on the screen

Performing a Casio E11 Reset

Use the stylus to press the RESET button.
• The unit performs a reset followed by a memory check operation
If no data error is found, the following two screens appear on the display in succession.
• Startup Screen
• Desktop
2. Normal unit operation is possible after the desktop appears.
• Since memory data and settings are retained, you can continue operation from where you last left off.
Important If the above operation does not solve the problem, perform a Casio E10 full reset.

Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: "A problem with memory contents has been found..."

Performing a Casio E-11 Full Reset

Important
• The following procedure deletes all data in memory. Be sure that data is backed up or that you no longer need it before performing the following procedure.
• If there is a CompactFlash card in the CASSIOPEIA's slot, remove the card before performing the full reset.
1. Make sure that unit power is turned On.
2. While holding down the 'Power' button, use the stylus to hold down the RESET button for about two seconds.
• This causes the following message to appear on the display screen. "Proceeding with this operation initializes memory. Press [Action] to proceed or I [Exit] to cancel."

3. Press the [Action] control.
• This causes the following message to appear on the display screen.
"Proceeding with this operation deletes all data stored in memory. Press [Action] to proceed or [Exit] to cancel."
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen.

You can abort the full reset operation while the messages in steps 2 and 3 are on the display by pressing the [Exit] button.

Errors Following a Full Reset

Either of the following two conditions can cause errors to continue, even after you perform a full reset.
• Hardware detect
• System problem caused by failure by you to correctly perform the reset procedure before using the unit for the first time

If you suspect that the problem is being caused because you did not properly reset the unit before using it for the first time, perform the following procedure.
This should correct the problem.

• Perform the following procedure if your CASSIOPEIA remains locked up even at you perform a full reset.
Important 
• The following operation deletes all data in CASSIOPEIA memory.
• If you previously backed up your CASSIOPIA data to your desktop computer hard disk or a CompactFlash memory card, you will be able to restore the data after performing the following operation.
• If backed up data includes data that is the cause of the original problem, your CASSIOPEIA may start malfunctioning again after data is resumed. In this case, you Will not be able to use the backed up data.
• To protect against backing up corrupted data that can cause problems when restored, first synchronize Pocket Outlook program data between your CASSIOPEIA and desktop computer. Next, use drag and drop to copy other files to you computer.

1. Remove both the main batteries and the back-up battery from the CASSIOPEIA.
2. Wait for about five minutes.
3. Reload the main batteries.
• Be sure to load the main batteries first. The CASSIOPEIA will not Operate properly if you load the back-up battery first. If you inadvertently load the back-up battery first, start over from step 1. above.
4. Reload the back-up battery.
5. Replace the battery cover and slide the battery cover lock to LOCK.
6. Wait for about five seconds and then press the [Power] button to turn on your CASSIOPEIA. • Turning on power displays the startup screen, following by the touch panel calibration screen.
7. Fllow the instructions that appear on the screen to make initial settings.
8. Alter setting up your CASSIOPEIA, turn it off.
• After completing the above procedure, you can restore ditit you have backed up on your desktop computer hard disk or CompactFlash memory card. See the separate Palm-size PC User's Guide for information about restoring backed up data.

Casio E-115 hard reset

Reset the Casio E115  Pocket PC and clear memory

To reset the Pocket PC
If your Pocket PC responds slowly, stops responding as expected, or “freezes,” try resetting it. A
reset causes the Pocket PC to restart and re-adjust memory allocation. Unsaved data in open
windows may be lost.
· Use the stylus to press and hold the Reset button for about two seconds.

To clear memory

If you forget your Pocket PC password or want to clear all data from your Pocket PC and return it
to the factory settings, clear memory.
Warning: Clearing memory deletes all data and restores the Pocket PC to its default settings.
Programs installed at the factory remain, while data you have created and programs you have
installed are erased.

1. Turn the Pocket PC on.
2. Press and hold the Power button, and use the stylus to press and hold the Reset button for
about two seconds.
3. If a message appears on the screen, confirm that you want to clear memory.
-or-
Remove the main and backup batteries, wait 5 minutes, and then reinsert them.

Casio E-125 hard reset

To reset the Pocket PC

If your Pocket PC responds slowly, stops responding as expected, or “freezes,” try resetting it. A
reset causes the Pocket PC to restart and re-adjust memory allocation. Unsaved data in open
windows may be lost.
• Use the stylus to press and hold the Reset button for about two seconds.

Casio E125 hard resetTo clear memory

If you forget your Pocket PC password or want to clear all data from your Pocket PC and return it
to the factory settings, clear memory.
Warning: Clearing memory deletes all data and restores the Pocket PC to its default settings.
Programs installed at the factory remain, while data you have created and programs you have
installed are erased.
1. Turn the Pocket PC on.
2. Press and hold the Power button, and use the stylus to press and hold the Reset button for
about two seconds.
3. If a message appears on the screen, confirm that you want to clear memory.
-or-
Remove the main and backup batteries, wait 5 minutes, and then reinsert them.

Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their
initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory
defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: “A problem with memory contents has been found...”
Performing a Full Reset
Important
• The following procedure deletes all data in memory. Be sure that data is backed up or
that you no longer need it before performing the following procedure.
• If there is a CompactFlash card in the CASSIOPEIA’s slot, remove the card before
performing the full reset.
1.Make sure that unit power is turned on.
2. While holding down the [Power] button, use the stylus to hold down the RESET
button for about two seconds.
• This causes the following message to appear on the display screen.
“Proceeding with this operation initializes memory. Press [Action] to proceed or
[Record] to cancel.”
3. Press the [Action] control.
• This causes the following message to appear on the display screen.
“Proceeding with this operation deletes all data stored in memory. Press [Action]
to proceed or [Record] to cancel.”
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen.
You can abort the full reset operation while the messages in steps 2 and 3 are on the
display by pressing the [Record] button.

Casio E-15 hard reset

Resetting the Casio E-15 Unit

"Reset" is similar to a computer reboot. Performing a reset deletes any data that is in the process of being input or edited, without yet being saved. Data stored in memory and all settings, however, are retained.
Perform the reset opeation whenever the unit fails to operate correctly due to operational error or some other abnormality. Any of the following symptoms indicate that reset is required.
• Failure of the unit is respond when the screen is tapped or a button is pressed
• The hourglass icon remaining on the screen

Performing a Reset

Use the stylus to press the RESET button.
• The unit performs a reset followed by a memory check operation
If no data error is found, the following two screens appear on the display in succession.
• Startup Screen
• Desktop
2. Normal unit operation is possible after the desktop appears.
• Since memory data and settings are retained, you can continue operation from where you last left off.
Important If the above operation does not solve the problem, perform a Casio E15 full reset.

Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: "A problem with memory contents has been found..."

Performing a Casio E-15 Full Reset

Important
• The following procedure deletes all data in memory. Be sure that data is backed up or that you no longer need it before performing the following procedure.
• If there is a CompactFlash card in the CASSIOPEIA's slot, remove the card before performing the full reset.
1. Make sure that unit power is turned On.
2. While holding down the 'Power' button, use the stylus to hold down the RESET button for about two seconds.
• This causes the following message to appear on the display screen. "Proceeding with this operation initializes memory. Press [Action] to proceed or I [Exit] to cancel."

3. Press the [Action] control.
• This causes the following message to appear on the display screen.
"Proceeding with this operation deletes all data stored in memory. Press [Action] to proceed or [Exit] to cancel."
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen.

You can abort the full reset operation while the messages in steps 2 and 3 are on the display by pressing the [Exit] button.

Errors Following a Full Reset

Either of the following two conditions can cause errors to continue, even after you perform a full reset.
• Hardware detect
• System problem caused by failure by you to correctly perform the reset procedure before using the unit for the first time

If you suspect that the problem is being caused because you did not properly reset the unit before using it for the first time, perform the following procedure.
This should correct the problem.

• Perform the following procedure if your CASSIOPEIA remains locked up even at you perform a full reset.
Important 
• The following operation deletes all data in CASSIOPEIA memory.
• If you previously backed up your CASSIOPIA data to your desktop computer hard disk or a CompactFlash memory card, you will be able to restore the data after performing the following operation.
• If backed up data includes data that is the cause of the original problem, your CASSIOPEIA may start malfunctioning again after data is resumed. In this case, you Will not be able to use the backed up data.
• To protect against backing up corrupted data that can cause problems when restored, first synchronize Pocket Outlook program data between your CASSIOPEIA and desktop computer. Next, use drag and drop to copy other files to you computer.

1. Remove both the main batteries and the back-up battery from the CASSIOPEIA.
2. Wait for about five minutes.
3. Reload the main batteries.
• Be sure to load the main batteries first. The CASSIOPEIA will not Operate properly if you load the back-up battery first. If you inadvertently load the back-up battery first, start over from step 1. above.
4. Reload the back-up battery.
5. Replace the battery cover and slide the battery cover lock to LOCK.
6. Wait for about five seconds and then press the [Power] button to turn on your CASSIOPEIA. • Turning on power displays the startup screen, following by the touch panel calibration screen.
7. Fllow the instructions that appear on the screen to make initial settings.
8. Alter setting up your CASSIOPEIA, turn it off.
• After completing the above procedure, you can restore ditit you have backed up on your desktop computer hard disk or CompactFlash memory card. See the separate Palm-size PC User's Guide for information about restoring backed up data.

Casio E-200 hard reset

Reset the Casio E-200 Pocket PC and clear memory

To reset the Pocket PC
If your Pocket PC responds slowly, stops responding as expected, or “freezes,” try resetting it. A
reset causes the Pocket PC to restart and re-adjust memory allocation. Unsaved data in open
windows may be lost.
• Use the stylus to press and hold the Reset button for about two seconds.

To clear memory Casio E-200 hard reset

Reset Cassiopeia E200 Casio E 200

If you forget your Pocket PC password or want to clear all data from your Pocket PC and return it
to the factory settings, clear memory.
Warning: Clearing memory deletes all data and restores the Pocket PC to its default settings.
Programs installed at the factory remain, while data you have created and programs you have
installed are erased.

1. Turn the Pocket PC on.
2. Press and hold the Power button, and use the stylus to press and hold the Reset button for
about two seconds.
3. If a message appears on the screen, confirm that you want to clear memory.
-or-
Remove the main and backup batteries, wait 5 minutes, and then reinsert them.

Casio E-3000 hard reset

Casio E-3000 hard reset

1. Power off your Casio E3000. Press the reset button and the power button together.

All Data will be lost! Make sure you have backed up your data.

Casio E-3000 full reset

1. Take out the battery slide it downwards.

2. Find the battery switch and slide it to OFF position.

3. Wait for 5 minutes.

4. Slide to the ON position.

5. Insert battery and turn off your phone.

You need to recalibrate your Casio E3000 pda.

Casio EG-800 hard reset

Casio EG-800 hard reset

To reset the Pocket PC
If your Pocket PC responds slowly, stops responding as expected, or “freezes,” try resetting
it. A reset causes the Pocket PC to restart and re-adjust memory allocation. Unsaved data in
open windows may be lost.

Use the stylus to press and hold the Reset button for about two seconds

Reset Cassiopeia EG800 EG 800

The conditions under which a system reset occurs during normal operation are as follows:
ACL (All Clear) reset
With conditions provided that no battery (neither main battery nor memory backup battery) is
being installed on the EG-800 and no power from the AC adapter is supplied, ACL reset will occur
when both batteries are put back and the power ON/OFF switch on the EG-800 is turned ON.
The DRAM data storage memory, program execution memory, and the specific memory for the
drivers will be “All-initialized (cleared)”. However, data on the Flash Disk can be retained without
modification.

EG-800 User reset

User reset will occur if the RESET switch is pressed while the system is operating (power is ON).
Nothing will happen if the RESET switch is pressed while the power is OFF.
With this operation the program execution memory in the DRAM and the working data not saved
will be “cleared”, but the data storage memory will be “retained”. Data on the Flash Disk will also
be retained.

Method of Initializing User Memory (Clear All Memory)
Press the “RESET switch” while holding down the Power ON/OFF switch while the power is ON.
In this operation a confirmation message querying whether it is okay to clear the memory will be
displayed twice. Each confirmation must be made with the “Action control button” and Program
button (“Voice key”) on the side of the EG-800 unit. If the “Action control button” is pressed for
both the first and repeated confirmation messages, the user memory (data storage memory and
program execution memory) will be cleared as the result of initialization. Pressing the “Voice key”
will cancel the All Clear reset and do a normal reset.

How to Recover Casio EG-800 If the Unit Crashes or Locks up
Follow the step below until the software lock is cleared.
Step:
1. Try to turn the power ON/OFF switch OFF and then ON.
2. Pull out the CF card or remove the EG-800 from the cradle.
3. Try a user reset (the program execution memory will be erased).
4. Try a ”Clear All Memory” (all memory areas will be cleared as the result of initialization).
5. As a last resort, remove the external power supply (AC Adaptor) and main battery from the
EG-800, and wait at least 48 hours for the memory backup battery to completely discharge.
Then, insert the main battery and turn on the power ON/OFF switch.

Casio EM-500 hard reset

Reset the Casio EM500  Pocket PC and clear memory

To reset the Pocket PC
If your Pocket PC responds slowly, stops responding as expected, or “freezes,” try resetting it. A
reset causes the Pocket PC to restart and re-adjust memory allocation. Unsaved data in open
windows may be lost.
• Use the stylus to press and hold the Reset button for about two seconds.
To clear memory
If you forget your Pocket PC password or want to clear all data from your Pocket PC and return it
to the factory settings, clear memory.
Warning: Clearing memory deletes all data and restores the Pocket PC to its default settings.
Programs installed at the factory remain, while data you have created and programs you have
installed are erased.

1. Turn the Pocket PC on.
2. Press and hold the Power button, and use the stylus to press and hold the Reset button for
about two seconds.
3. If a message appears on the screen, confirm that you want to clear memory.
-or-
Remove the main and backup batteries, wait 5 minutes, and then reinsert them.

Full Reset (Memory Initialize)
Full reset (memory initialize) deletes all data, and resets all unit parameters to their
initial defaults.
The following are conditions when you should perform a full reset.
• When you want to delete all memory data and return unit settings to their factory
defaults
• When you forget your password and need to clear it
• When a data error causes operational problems
• Appearance of the message: “A problem with memory contents has been found...”
Performing a Full Reset
Important
• The following procedure deletes all data in memory. Be sure that data is backed up or
that you no longer need it before performing the following procedure.
• If there is a MultiMediaCard in the CASSIOPEIA’s slot, remove the card before
performing the full reset.
1. Make sure that unit power is turned on.
2. While holding down the [Power] button, use the stylus to hold down the RESET
button for about two seconds.
• This causes the following message to appear on the display screen.
“Proceeding with this operation initializes memory. Press [Action] to proceed or
[Record] to cancel.”
3. Press the [Action] control.
• This causes the following message to appear on the display screen.
“Proceeding with this operation deletes all data stored in memory. Press [Action]
to proceed or [Record] to cancel.”
4. Press the [Action] control again.
• This starts the full reset operation, which deletes all data in memory.
• Pressing the [Action] control displays the Startup screen.
You can abort the full reset operation while the messages in steps 2 and 3 are on the
display by pressing the [Record] button.

Errors Following a Full Reset

Either of the following two conditions can cause errors to continue, even after you
perform a full reset.
• Hardware defect
• System problem caused by failure by you to correctly perform the reset procedure
before using the unit for the first time

• Perform the following procedure if your CASSIOPEIA remains locked up even after
you perform a full reset.
Important
• The following operation deletes all data in CASSIOPEIA memory.
• If you previously backed up your CASSIOPEIA data to your desktop computer hard
disk or a MultiMediaCard, you will be able to restore the data after performing the
following operation.
• If backed up data includes data that is the cause of the original problem, your
CASSIOPEIA may start malfunctioning again after data is restored. In this case, you
will not be able to use the backed up data.
• To protect against backing up corrupted data that can cause problems when restored,
first synchronize Pocket Outlook program data between your CASSIOPEIA and
desktop computer. Next, use drag and drop to copy other files to you computer.

1. Remove both the main battery and the backup battery from the CASSIOPEIA.
2.Wait for about five minutes.
3. Reload the main battery.
• Be sure to load the main battery first. The CASSIOPEIA will not operate properly if
you load the backup battery first. If you inadvertently load the backup battery first,
start over from step 1 above.
4. Attach the AC adapter and charge the battery pack.
5. Reload the backup battery.
6. Make sure the battery cover switch is in the LOCK position.
7.Wait for about five seconds and then press the [Power] button to turn on your
CASSIOPEIA.
• Turning on power displays the startup screen, following by the touch panel
calibration screen.
8. Follow the instructions that appear on the screen to make initial settings.
9. After setting up your CASSIOPEIA, turn it off.
• After completing the above procedure, you can restore data you have backed up on
your desktop computer hard disk or MultiMediaCard.

Casio IT-10 M20 hard reset

3 Reset switch This switch resets the terminal, similar to turning off and on the power
switch. Reset the terminal when some abnormality occurs, such as if the
buttons or tap operations stop working

Casio IT-10 M20 BR hard reset

3 Reset switch This switch resets the terminal, similar to turning off and on the power
switch. Reset the terminal when some abnormality occurs, such as if the
buttons or tap operations stop working

Cingular 2125 hard reset

How to hard reset Cingular 8125

9 Voice Command Press to start Voice Speed Dial; press and hold to
record a voice note.
10 Infrared Port Let you exchange file(s) or data with other devices
wirelessly.
11 RESET Button With the stylus, press the RESET button to soft-reset
your device.
12 CAMERA Button Press to launch the camera. Press again when in
camera mode to take a picture or record a video clip.

Resetting Your Pocket PC Phone (Soft reset)
Occasionally you may need to reset your Pocket PC Phone. A normal
(or soft) reset of your device clears all active program memory and
shuts down all active programs. This can be useful when the device is
running slower than normal, or a program is not performing properly. A
soft reset is also necessary after the installation of some programs. If a
soft reset is performed when programs are running, unsaved work will
be lost.
You can also perform a hard reset (also known as a full reset). A hard
reset should be performed only if a normal reset does not solve a
system problem. After a hard reset, the device is restored to its default
settings — the way it was when you first purchased it and turned it
on. Any programs you installed, data you entered, and settings you
customized on the device will be lost. Only Windows MobileTM software
and other pre-installed programs will remain.

To perform a soft reset

• Use the stylus to lightly press and hold the RESET button on the left side of your device. The device restarts and displays the Today screen.

Warning! Always turn off your device before performing a soft reset or
installing/replacing the battery and SIM card.

To perform a hard reset

1. Press and hold the Comm Manager button and Voice Command button on the device.
2. Keep the two buttons pressed, and at the same time, use the stylus to lightly press and hold the RESET button.

Cingular 8100 hard reset

How to hard reset Cingular 8100

9 Voice Command Press to start Voice Speed Dial; press and hold to
record a voice note.
10 Infrared Port Let you exchange file(s) or data with other devices wirelessly.
11 RESET Button With the stylus, press the RESET button to soft-reset your device.
12 CAMERA Button Press to launch the camera. Press again when in camera mode to take a picture or record a video clip.

Resetting Your Pocket PC Phone (Soft reset)
Occasionally you may need to reset your Pocket PC Phone. A normal (or soft) reset of your device clears all active program memory and
shuts down all active programs. This can be useful when the device is running slower than normal, or a program is not performing properly. A
soft reset is also necessary after the installation of some programs. If a soft reset is performed when programs are running, unsaved work will
be lost.
You can also perform a hard reset (also known as a full reset). A hard reset should be performed only if a normal reset does not solve a
system problem. After a hard reset, the device is restored to its default settings — the way it was when you first purchased it and turned it
on. Any programs you installed, data you entered, and settings you customized on the device will be lost. Only Windows MobileTM software
and other pre-installed programs will remain.

To perform a soft reset

• Use the stylus to lightly press and hold the RESET button on the left side of your device.
• The device restarts and displays the Today screen.

Warning! Always turn off your device before performing a soft reset or installing/replacing the battery and SIM card.

To perform a 8100 hard reset

1. Press and hold the Comm Manager button and Voice Command button on the device.
2. Keep the two buttons pressed, and at the same time, use the stylus to lightly press and hold the RESET button.

Cingular 8125 hard reset

How to hard reset Cingular 8125

9 Voice Command Press to start Voice Speed Dial; press and hold to record a voice note.
10 Infrared Port Let you exchange file(s) or data with other devices wirelessly.
11 RESET Button With the stylus, press the RESET button to soft-reset your device.
12 CAMERA Button Press to launch the camera. Press again when in camera mode to take a picture or record a video clip.

Resetting Your 8125 Pocket PC Phone (Soft reset)

Occasionally you may need to reset your Pocket PC Phone. A normal
(or soft) reset of your device clears all active program memory and
shuts down all active programs. This can be useful when the device is
running slower than normal, or a program is not performing properly. A
soft reset is also necessary after the installation of some programs. If a
soft reset is performed when programs are running, unsaved work will
be lost.
You can also perform a hard reset (also known as a full reset). A hard
reset should be performed only if a normal reset does not solve a
system problem. After a hard reset, the device is restored to its default
settings — the way it was when you first purchased it and turned it
on. Any programs you installed, data you entered, and settings you
customized on the device will be lost. Only Windows MobileTM software
and other pre-installed programs will remain.

To perform a soft reset

• Use the stylus to lightly press and hold the RESET button on the left side of your device.
• The device restarts and displays the Today screen.

Warning! Always turn off your device before performing a soft reset or installing/replacing the battery and SIM card.

To perform a Cingular 8125 hard reset

1. Press and hold the Comm Manager button and Voice Command button on the device.
2. Keep the two buttons pressed, and at the same time, use the stylus to lightly press and hold the RESET button.