MiTAC Mio 269 hard reset

Clearing the Mio 269 Memory

NOTE (for Mio 268 Only): Clearing the memory will cause the navigation software to lose. You must insert the Mio Map card to perform the automatic installation. In case the data in the Mio Map card is lost or damaged, perform the “Recover” procedure.
If your device still does not respond after being reset, you can use the following steps to clear the memory.
1. Disconnect all cables, including the AC adapter, from your device.
2. Use the stylus to slide the ON/OFF switch to the OFF (left) position.
3. For Mio 268 only: Insert the Mio Map card to your device.
4. Wait for 1 minute and then slide the switch back to the ON (right) position

5. Your device will perform the initial start up.

MiTAC Mio 168 hard reset

Resetting Your MiTAC Mio 168 Pocket PC

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:

After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side
of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

CAUTION: To ensure the integrity of your data should it be necessary to clear the memory, you’re
advised to regularly back up your data.

Do not slide the battery switch unless it is necessary

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping WIN Start > Settings > System tab > Memory icon > Running
Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. Your Pocket PC will automatically turn on and prompt you to start the setup wizard.
7. Follow the onscreen instructions to complete the setup wizard.

8. Reestablish a partnership with your desktop computer.
9. You may also want to restore data to your Pocket PC from your most recent
backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 169 hard reset

MiTAC Mio 169 hard reset

Resetting Your MiTAC Mio 169 System
Resetting your system is similar to restarting your computer. Occasionally, you may need to reset your device. For example, you should reset your system when it stops responding; or appears to be “frozen” or “locked up.”
To reset your system, use the stylus pen to press the Reset button on top of your device.

If your device still does not respond after being reset, you can use the following steps to clear the memory, and reset the system settings to factory defaults.
1. Disconnect all cables, including the AC adapter, from your device.

2. Use the stylus pen to slide the ON/OFF switch to the OFF (right) position.
3. Wait for 1 minute and then slide the switch back to the ON (left) position.
4. Your device will automatically turn on and the Main screen will appear.
NOTE: Once you clear the memory with this ON/OFF switch, all the settings you have changed in the System Settings will be erased. You will need to re-enter any personal settings, including time and date once again.

MiTAC Mio 180 hard reset

Mio 180 Soft reset

Press the reset button to restart Digiwalker 180

Mio 180 hard reset

Follow this procedure to restore your Pocket PC to the last state when your Pocket PC does not respond after being reset.

1. Disconnect all cables, including the AC adapter, from your Pocket PC.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position. Mio 180 restarting after hard reset.

MiTAC Mio 268 hard reset

Clearing the Mio 268 Memory

NOTE (for Mio 268 Only): Clearing the memory will cause the navigation software to lose. You must insert the Mio Map card to perform the automatic installation. In case the data in the Mio Map card is lost or damaged, perform the “Recover” procedure.
If your device still does not respond after being reset, you can use the following steps to clear the memory.
1. Disconnect all cables, including the AC adapter, from your device.
2. Use the stylus to slide the ON/OFF switch to the OFF (left) position.
3. For Mio 268 only: Insert the Mio Map card to your device.
4. Wait for 1 minute and then slide the switch back to the ON (right) position

5. Your device will perform the initial start up.

MiTAC Mio 336 BT hard reset

Resetting Your MiTAC Mio 336 BT Pocket PC
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC;
for example, you should reset:
After you restore data from your desktop
computer.
When your Pocket PC stops responding; in other
words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side
of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected).
Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping WIN Start
Settings > System tab > Memory icon > Running
Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the
OFF (up) position.
5. Wait for 1 minute and then slide the switch back
to the ON (down) position.
6. Your Pocket PC will automatically turn on and
display the Welcome screen.
7. To begin the Welcome Wizard, tap the screen
with the stylus and follow the onscreen
instructions to complete the Welcome Wizard.

8. Reestablish a. partnership with your desktop computer.
9. You may also want to restore data to your Pocket PC from your most recent
backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 338 hard reset

MiTAC Mio 338 soft reset

Press the reset hole on the left side of the Mio 338 to restart your PDA.

Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:
After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the side of your Pocket PC.

MiTAC Mio 338 hard reset

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping Win Start > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Use the stylus to slide the battery switch to the OFF (up) position.
5. Wait for 1 minute and then slide the switch back to the ON (down) position.
6. The red notification indicator on your Pocket PC will flash for approximately 30 seconds. Then your Pocket PC will automatically turn on and display the Welcome screen.
7. To begin the Welcome Wizard, tap the screen with the stylus and follow the onscreen instructions to complete the Welcome Wizard.
8. Restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

MiTAC Mio 339 hard reset

Resetting Your Mio 339 Pocket PC

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your
Pocket PC; for example, you should reset:
After you restore data from your desktop computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket PC:
1. Remove the SD/MMC card (if installed).
2. Use the stylus to press the reset button on the rear of your Pocket PC.


Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default state by clearing the memory (RAM) from your Pocket PC. For example, you should clear the memory:
When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping Start > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Remove the battery door.
5. Use the stylus to slide the battery switch to the OFF (left) position.
6. Wait for 1 minute and then slide the switch back to the ON (right) position.

7. The red notification indicator on your Pocket PC will flash for approximately 30 seconds. Then
your Pocket PC will automatically turn on and display the Welcome screen.
8. To begin the Welcome Wizard, tap the screen with the stylus and follow the onscreen instructions to complete the Welcome Wizard.
9. Reestablish a. partnership with your desktop computer.
10. You may also want to restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get
the same result as you restore the factory default state.

MiTAC Mio 558 hard reset

Resetting Your Pocket PC
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It
restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:
After you restore data from your desktop
computer.
When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”
Follow this procedure to reset your Pocket
PC:
1. Remove the SD/MMC and/or CompactFlash card (if installed).
2. Use the stylus to press the reset button on the rear of your Pocket PC.

Restoring Factory Default State
In some cases, you may need to restore your Pocket PC to the factory default
state by clearing the memory (RAM) from your Pocket PC. For example, you
should clear the memory:

When your Pocket PC does not respond after being reset.
When you forget your password.
Clearing the memory means all data you have entered in RAM, including all
files, system settings and additional programs you have installed, will be erased.
(Programs installed to ROM at the factory are not affected.)

Follow this procedure to clear the memory from your Pocket PC:
1. Backup your information if necessary.
2. Disconnect all cables, including the AC adapter, from your Pocket PC.
3. Stop all running programs by tapping > Settings > System tab > Memory icon > Running Programs tab > Stop All.
4. Press the battery lock to remove the battery.
5. Use the stylus to slide the battery switch to the OFF (left) position.
6. Wait for 1 minute and then slide the switch back to the ON (right) position.
7. Your Pocket PC will automatically turn on and display the “Welcome” screen.
NOTE: In case your Pocket PC didn’t automatically turn on, use the stylus to firmly press the RESET button at the back
of your Pocket PC to turn it on.
8. To begin the Welcome Wizard, tap the screen with the stylus and follow the
onscreen instructions to complete the Welcome Wizard.

9. Reestablish a partnership with your desktop computer.
10. You may also want to restore data to your Pocket PC from your most recent backup file.
NOTE: If the battery completely runs out of power and is not charged in time, you will get the same result as you restore the factory default state.

MiTAC Mio 8390 hard reset

Restoring Factory Default State
NOTE
You are recommended to ask your local dealer for service. Avoid restoring factory default state by yourself.
In some cases, you may need to restore your Smartphone to the factory default state by clearing the memory (RAM) from your Smartphone. For example, you should clear the memory:
When your Smartphone cannot be turned on.
When you forget your password.
When you want to remove the add-on software.
When you wish to return, dispose of, or sell your Smartphone.

Clearing the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.

Follow this procedure to clear the memory from your Smartphone:
1. To keep the data stored in your Smartphone, back up your data to your desktop computer using ActiveSync, and restore it after the memory is cleared.
2. Connect the AC adapter, and disconnect all other cables.
3. Make sure that your Smartphone is turned off.
4. Press and hold the Volume control. When holding it, press and hold the End key for four seconds to turn on your Smartphone, and then let go of the End key .
5. After the Smartphone vibrates twice, you can let go of the Volume control.
6. Your Smartphone will turn on after about two minutes.
7. Re-install the add-on software, if necessary.
8. Restore your backup, if necessary.

MiTAC Mio 8870 hard reset

Mio 8870 hard reset

Restoring Factory Default State

You are recommended to ask your local dealer for service. Avoid restoring factory default state
by yourself

In some cases, you may need to restore your Smartphone to the factory default state by
clearing the memory (RAM) from your Smartphone. For example, you should clear the
memory:

When your Smartphone cannot be turned on.
When you forget your password.
When you want to remove the add-on software.
When you wish to return, dispose of, or sell your Smartphone.

Clearing the memory means all data you have entered in RAM, including all files, system
settings and additional programs you have installed, will be erased.

Follow this procedure to clear the memory from your Smartphone:

1. To keep the data stored in your Smartphone, back up your data to your desktop computer
using ActiveSync, and restore it after the memory is cleared.
2. Connect the AC adapter, and disconnect all other cables.
3. Make sure that your Mio 8870 Smartphone is turned off.

4. Press and hold the Volume control. When holding it, press and hold the End key for four seconds to turn on your Smartphone, and then let go of the End key.

5. After the Smartphone vibrates twice, you can let go of the Volume control.
6. Your Smartphone will turn on after about two minutes.
7. Re-install the add-on software, if necessary.
8. Restore your backup, if necessary.

Yes tested this way try this way i hope solve your problem

MiTAC Mio A501 hard reset

Mitac Mio A501 Soft reset

Resetting Your Device

CAUTION: Resetting will cause unsaved data to be lost.
Resetting the device is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset the device; for example, you should reset when the device stops responding; in other words, it appears to be frozen or locked up.
Use the stylus to press the reset button on the device.

Mitac Mio A501 Hard reset

Restoring Factory Default State

In some cases, you may need to restore the device to the factory default state by clearing the memory from the device. For example, you should clear the memory:

• When the device does not respond after being reset.
• When you forget your password.

Clearing the memory means all data you have entered in the device's memory, including all files, system settings and additional programs you
have installed, will be erased. (Programs installed to ROM at the factory are not affected.)
CAUTION: To ensure the integrity of your data should it be necessary to clear the memory, you are advised to regularly back up your data.

Follow this procedure to clear the memory from the device:

1. Make sure that the device is turned off.

2. Press the Power button on the top of the device, and then press and hold the Talk button  on the front panel until the device vibrates.
3. The device will turn on automatically. The backlight of the keypad will glow, and the setup wizard will appear on the screen. Follow the
on-screen instructions to complete the setup wizard.
4. Re-establish a partnership with your desktop computer.
5. Re-install the add-on software, if necessary.

try this way i hope solve your problem 

MiTAC Mio A700 hard reset

Mitac Mio A700 soft reset

Press the RESET hole on Mio A700 to restart.

Mitac Mio A700 hard reset

To clear the memory device:
1. Make sure that A700 is turned off.
2. Press and hold the volume down and the END CALL red button.
3. After the vibration .
4. A700 automatically turn on. Lights up the keyboard and the screen setup wizard appeare. Follow the instructions on the screen.
5. Restore the partnership with your desktop PC.
6. Reinstall the necessary additional software.

MiTAC Mio A701 hard reset

Mitac Mio A701 Hard reset  Soft reset

Resetting Your Mio A701
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your A701 is similar to restarting your desktop computer. It restarts
the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your A701;
for example, you should reset when your A701
stops responding; in other words, it appears to be
“frozen” or “locked up.”
Use the stylus to press the reset button on your
A701.

Restoring Factory Default State A701 Hard reset

In some cases, you may need to restore your A701 to the factory default state by
clearing the memory from your A701. For example, you should clear the
memory:

• When your A701 does not respond after being reset.
• When you forget your password.

Clearing the memory means all data you have entered in A701’s memory,
including all files, system settings and additional programs you have installed,
will be erased. (Programs installed to ROM at the factory are not affected.)
CAUTION: To ensure the integrity of your data should it be necessary to clear the
memory, you are advised to regularly back up your data.

Follow this procedure to clear the memory from your A701:

1. Make sure that A701 is turned off.
2. Press and hold the Down Volume button. When holding it, press and hold the  End button.
3. After A701 vibrates, you can let go of both buttons.
4. A701 will turn on automatically. The backlight of the keypad will glow, and the setup wizard will appear on the screen. Follow the on-screen
instructions to complete the setup wizard.
5. Re-establish a partnership with your desktop computer.
6. Re-install the add-on software, if necessary.

MiTAC Mio A702 hard reset

Mitac Mio A702 Soft reset

Use the stylus to press the reset button on the
device

In some cases, you may need to restore the device to the factory default state
by clearing the memory from the device. For example, you should clear the
memory:

• When the device does not respond after being reset.

• When you forget your password.

Clearing the memory means all data you have entered in the device’s
memory, including all files, system settings and additional programs you
have installed, will be erased. (Programs installed to ROM at the factory are
not affected.)
CAUTION: To ensure the integrity of your data should it be necessary to clear the
memory, you are advised to regularly back up your data.

Mitac Mio A702 hard reset

Follow this procedure to clear the memory from the device:

1. Make sure that the device is turned off.
2. While pressing and holding the Power button, press and hold the Talk
button until the device vibrates.
3. The device will turn on automatically. The backlight of the keypad will
glow, and the setup wizard will appear on the screen. Follow the
on-screen instructions to complete the setup wizard.
4. Re-establish a partnership with your desktop computer.
5. Re-install the add-on software, if necessary.

yes 100% tested way try this i hope solve your problem

MiTAC Mio H610 hard reset

MiTAC Mio H610 Soft Reset

Resetting Your System
Occasionally, you may need to reset your device. For example, you should reset your system when it stops
responding; or appears to be frozen or locked up.
Insert a small rod, such as a straightened paperclip, into the reset button of your device. This is called a soft
reset. The Home screen should appear after a soft reset.

2 Reset Button: Restarts your device (soft reset).

How can I reset my Mio H610?

MiTAC Mio H610 Soft Reset

If your device is not working properly. you can try a soft reset. On the right hand side of your device. you'll find a small opening. containing the reset button. Push it once with the tip of the stylus at the end of wrist strap to perform a soft reset.

MiTAC Mio H610 Soft Reset

You can also restart your Mio H610 by tapping the Restart icon.

MiTAC Mio H610 Hard Reset

If this does not solve your problem. You may try a hard reset. Pushing the on/off button for 4 to 5 seconds will hard reset your device. Push the button again for 4 to 5 seconds to start it up again.
tested way try this i hope solved your problem not solve comments plz itry your help

MiTAC Mio P340 hard reset

Mitac Mio P340 Soft reset

Resetting Your Pocket PC
CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
Occasionally, you may need to reset your Pocket PC; for example, you should reset:

• After you restore data from your desktop computer.

• When your Pocket PC stops responding; in other words, it appears to be frozen or locked up.

Use the stylus to press the reset button on your Pocket PC.

Mitac Mio P340 Hard reset

Restoring Last State
Follow this procedure to restore your Pocket PC to the last state when your
Pocket PC does not respond after being reset.
1. Disconnect all cables, including the AC adapter, from your Pocket PC.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position.

4. Your Pocket PC turns on.
NOTE: You need to restore your Pocket PC to factory default state if you have set up a password but forget it.

100% tested way tested this 

MiTAC Mio P360 hard reset

Resetting your Pocket PC Mio P360 Soft reset

CAUTION! Resetting will cause unsaved data to be lost.

Resetting your Pocket PC allows you to restart the operating system, but you will lose any unsaved data.

Occasionally you may need to reset your Pocket PC, for example you should reset your mio p360 when it stops responding.

In other words it appears frozen or locked up. Follow the procedure to reset Mio P360:

1. Slide the ON/OFF switch to the OFF position.
2. Wait for 1 minute and then slide the switch back to the ON position.
3. Mio P360 turns ON.

Mio P360 Hard reset

Restoring the factory default state of Mio P360

In some cases, you may need to restore your Pocket PC to the factory default state by
clearing the memory (RAM) from your Pocket PC. For example, yshould clear the memory:

• the factory default state does not respond after soft reset.
• When you forget your password.

Claring the memory means all data you have entered in RAM, including all files, system settings and additional programs you have installed, will be erased.

NOTE: The files stored in My Flash DISK will not be erased.

1. Disconnect all cables, including the AC charger, from your POCKET PC.
2. Push the navigation stick upward and slide the ON/OFF switch to the position.
3. While holding the navigation stick, slide the switch back to ON again.
4. Your Pocket PC turns on and performs the initial start up.

MiTAC Mio P350 hard reset

Mitac Mio P350 Soft reset

Resetting Your Pocket PC - Soft reset

CAUTION: Resetting will cause unsaved data to be lost.

Resetting your Pocket PC is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
reset:

• After you restore data from your desktop computer.

• When your Pocket PC stops responding; in other words, it appears to be “frozen” or “locked up.”

Use the stylus to press the reset button on your Pocket PC.

Restoring Last State - Mitac Mio p350 Hard reset

Follow this procedure to restore your Pocket PC to the last state when your Pocket PC does not respond after being reset.

1. Disconnect all cables, including the AC adapter, from your Pocket PC.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position.

4. Your Pocket PC turns on.

Mitac Mio P350 Hard reset

To reset your Mio p350 to factory default settings:

Press up button during cold boot until splash screen is shown


OR


Tap

Start menu > Settings > System > SysInfo

Then tap Clean Boot tab

To reset the device to the factory default settings tap Start and input 000, (3 null) as shown below, then tap OK. Mio P550m restarting.

 

try this i hope solved your problem i try this way 100% tested thic way

MiTAC Mio P550 hard reset

Resetting Your Mio P550 Pocket PC - Soft reset

CAUTION: Resetting will cause unsaved data to be lost.
Resetting your Pocket PC is similar to restarting your desktop computer. It restarts the operating system, but you will lose any unsaved data.
reset:

• After you restore data from your desktop computer.

• When your Pocket PC stops responding; in other words, it appears to be frozen or locked up.

Use the stylus to press the reset button on your Pocket PC.

Restoring Last State - Mitac Mio P550 Hard reset

Follow this procedure to restore your Pocket PC to the last state when your Pocket PC does not respond after being reset.

1. Disconnect all cables, including the AC adapter, from your Pocket PC.
2. Slide the ON/OFF switch to the OFF position.
3. Wait for 1 minute and then slide the switch back to the ON position.

4. Your Pocket PC turns on.

Mitac Mio P550 Hard reset

To reset your Mio P550 to factory default settings:

Press up button during cold boot until splash screen is shown


OR via menu

Tap

Start menu > Settings > System > SysInfo, then tap Clean Boot tab

Then tap Clean Boot tab

To reset the device to the factory default settings tap Start and input 000, (3 null) as shown below, then tap OK. Mio P550 restarting.

 

Try this i hope solve your problem i'm tested this way